ANAN-G2-1K 1000W HF & 6M SDR Transceiver Booking

$5495.00 $5495.00
  • Description
  • Technical Specifications

Please Note that Apache Labs does not accept payment via Online Bank Wire transfers due to online fraud.



1500W (High Power Mode), 800W (low Power Mode)

Please note we are currenty Not taking any new orders for this product due to a backlog of the preorders, once all preorders have been fulfilled we will commence taking new orders.

Please note Pictures of the unit will be updated shortly.

The G2 (Gen2 SDR) provides the same stellar Receiver and transmitter performance as the earlier ANAN radios, however, it provides a huge leap forward in processing capability and flexibility in use case scenarios. 

  • Large FPGA with 930 GMAC/s of processing capability
  • Built-in Linux OS with Desktop running on a quad core Arm platform
  • Capable of Stand-Alone operation without a PC
  • Use it with a PC running Thetis
  • Hardware capable of remote operation (please note this is a future feature set not currently available)
  • Rich I/Os - 2 x HDMI 4K, Gigabit Ethernet, 2 x USB

Watch this to get to learn more about the Gen2 Platform


  ANAN-7000/8000DLE MKII ANAN-G2 
FPGA DSP Peak Processing capacity 240 GMAC/s 930 GMAC/s
Number of DDCs 8 10
Stand-Alone Capability No Yes
Thin Client/Remote Capability No Hardware Capable (Future Feature Set)
Protocol 2 Support Beta Fully Supported
Built-in CPU No Yes
Balanced Audio Input No




General Specifications:

  • Architecture: Direct Sampling DDC/DUC Transceiver
  • Microprecessor controlled protection for SWR, Temperature, Voltage/Current (Over or Under)
  • Interface: Ethernet
  • Phase Noise (Clock): -149dB @ 10Khz
  • TCXO Stability (Typical): /- .1 PPM
  • Modes: CW, SSB, NFM, AM, Digital
  • Antenna Ports: Three SO-239 50 ohms Software Configurable Ports, One BNC for RX2
  • Frequency Resolution: 1 Hz


Electrical Specifications:

  • 100-250v AC


Mechanical Specifications:

  • 15Kg (approx. Weight)
  • 49.7cm L x 38.4cm W x 13.8cm H (not including extrusions)


Receiver Specifications:

  • Receiver Architecture: Direct Down Conversion
  • Dual 16 bit Phase Synchronous ADCs
  • Independent filter banks for each ADC
  • 10/6M LNAs
  • Frequency Coverage: 9Khz to 60Mhz
  • Attenuator: 1-30dB step attenuator
  • Reciprocal Mixing Dynamic Range (RMDR): 116dB @ 2Khz
  • Receiver Phase noise: -149dB @ 10Khz
  • Image rejection: 100dB
  • Hardware support for 7 independent receivers assignable to either ADC


Transmitter Specifications:

  • Transmitter Architecture: Direct Up Conversion
  • DAC Resolution: 16 bit
  • RF Output Power (Maximum): 1000W PEP: SSB/CW. 500W:  FM, RTTY, Digital. 275W: AM
  • IMD: IMD3 typically -72dB @ 1000W PEP output on 20M
  • Harmonics: Typically better than -50dBc on HF and -60dBc on 6M
  • Carrier and Opposite Sideband Suppression: Better than -80dBc
  • Transverter IF Output: 0db to 15dB



  • RCA Line In, Digital In, PTT in, PTT Out
  • DB9 Seven Software configurable Open Collector Outputs
  • SMA XVTR TX Out, 10Mhz Reference Input
  • 6.25mm Barrel Mic, CW Key, Headphones and Speaker Outputs
  • SMA PureSignal (Predistortion) Loop Input and Output
  • RJ45 Ethernet LAN Connector
  • 2 x HDMI
  • 2 x USB



Subscribe Newsletter
To get the latest scoop right to your inbox.

Help Centre