Any idea why CPU Meter is not displaying at all and volt / amp meter does not update. Tried selecting and unselecting volts-amps in settings, but nothing changes. see snip below
CPU Volts and Amp meters not working V 2.9.0.6
Re: CPU Volts and Amp meters not working V 2.9.0.6
No problem here, normal readings at tx (compared to p/s reading), zero amp at rx. Looks ok for me.
73, Norbert - DL8LAQ - ANAN-G2 w/display - Richie's latest Thetis version and pihpsdr by N1GP&DL1YCF
Re: CPU Volts and Amp meters not working V 2.9.0.6
7000DLE, f/w 2.1.18
73, Norbert - DL8LAQ - ANAN-G2 w/display - Richie's latest Thetis version and pihpsdr by N1GP&DL1YCF
Re: CPU Volts and Amp meters not working V 2.9.0.6
Maybe you need to upgrade the firmware?
2.1.23 here with 7000DLE MKII works OK.
2.1.23 here with 7000DLE MKII works OK.
Mike W9MDB
Re: CPU Volts and Amp meters not working V 2.9.0.6
To clarify the firmware angle: versions beyond 2.1.18 were never formally released past very limited alpha testing, and there have been no changes to voltage and current data handling since 2.1.18. So it most likely is not the firmware.
Re: CPU Volts and Amp meters not working V 2.9.0.6
7000DLE, f/w 2.1.18
tried on other computer and it works fine, so it is not hardware or firmware related, was running v2.9.0.6
uninstalled and erased all files related to thetis, and then reinstalled and started from scratch database and all and it still does not work.
however it did work at one time with V2.9.0.6 on windows 11. going to have to do a clean windows 11 install.
tried on other computer and it works fine, so it is not hardware or firmware related, was running v2.9.0.6
uninstalled and erased all files related to thetis, and then reinstalled and started from scratch database and all and it still does not work.
however it did work at one time with V2.9.0.6 on windows 11. going to have to do a clean windows 11 install.
Re: CPU Volts and Amp meters not working V 2.9.0.6
I have a brand new 7000 DLE MK3 delivered a few days ago, running a new fresh install of Thetis 2.9.0.6, and Protocol 1 due to the chip change. Current metering on the radio does not work at all.
Can anyone else with a new Mk3 confirm they also dont have current metering?
There are also other broken things, like unable to switch Tx antennas from the drop down menus, and many other things. Poor showing from Apache.
Can anyone else with a new Mk3 confirm they also dont have current metering?
There are also other broken things, like unable to switch Tx antennas from the drop down menus, and many other things. Poor showing from Apache.
Re: CPU Volts and Amp meters not working V 2.9.0.6
As for "other broken things, like unable to switch Tx antennas "
Setup setting General- Ant/Filters-Antenna : uncheck the "Do Not TX" tick boxes (under Antenna 2 and 3.)
Setup setting General- Ant/Filters-Antenna : uncheck the "Do Not TX" tick boxes (under Antenna 2 and 3.)
73 PD3LK Leon
Re: CPU Volts and Amp meters not working V 2.9.0.6
7000DLE MKII F/W Ver 2.7
I have the same issue. I'm running Windows 10, Thetis V2.9.0.6
I just upgraded from V 2.8 hoping that would fix the problem.
It did not.
I have the same issue. I'm running Windows 10, Thetis V2.9.0.6
I just upgraded from V 2.8 hoping that would fix the problem.
It did not.
Re: CPU Volts and Amp meters not working V 2.9.0.6
Running Thetis 2.9.0.6. Voltage displays correctly; amps always zero. (7000DLE)
Rick
K8EZB
Rick
K8EZB