I am on Thetis 2.9.06 x64 and attempted to adjust TX bandwidth using my mouse but it didn't pan out. No doubt my settings aren't right.
Two screen-captures below for reference.
What am I missing?
JJ
Can't adjust TX bandwidth using mouse
Can't adjust TX bandwidth using mouse
PC: 8 Core i7-10700 CPU @ 2.90GHz, NVMe SK Hynix 512 GB SSD, 32GB RAM
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Re: Can't adjust TX bandwidth using mouse
Didnt know the mouse wheel could adjust the TX bandwidth. How are you doing that?
Gary NC3Z
Re: Can't adjust TX bandwidth using mouse
There is no interactive adjustment of the TX transmit bandwidth in the spectrum when in receive. It can only be done using the up/down number controls on the main gui (just above the TX FL button), or in setup in the Transmit tab (Transmit filter).
It can be adjusted with the mouse in the spectrum when in TX, however there are some issues with it which need to be fixed. I have never used it like that personally.
Remember, TX bandwidth is stored per TX profile, so adjustments you make will be temporary unless the TX profile is saved.
It can be adjusted with the mouse in the spectrum when in TX, however there are some issues with it which need to be fixed. I have never used it like that personally.
Remember, TX bandwidth is stored per TX profile, so adjustments you make will be temporary unless the TX profile is saved.
Richie - MW0LGE - https://www.qrz.com/db/mw0lge
Latest Release [2.10.3.5] : https://github.com/ramdor/Thetis/releases/tag/v2.10.3.5
Latest Work In Progress : https://github.com/ramdor/Thetis/releas ... .3.6-dev_2
Latest Release [2.10.3.5] : https://github.com/ramdor/Thetis/releases/tag/v2.10.3.5
Latest Work In Progress : https://github.com/ramdor/Thetis/releas ... .3.6-dev_2
Re: Can't adjust TX bandwidth using mouse
Gary, Richie,
Gary:
I can't but a buddy of mine in Florida can and he uses the same exact Thetis version that I do (except that his works in P2, but I don't think that has anything do with this).
Richie:
Ditto above.....my buddy told me that when the mouse cursor morphs into a double arrow line I can drag the TX band-width by clicking the left mouse button and then just drag the bandwidth out. This, just to experiment rather than save anything necessarily. He did it on the fly while we were in contact the other day and I just tried to do the same.....
Thanks again for the feedback!
JJ
NI2M
Gary:
I can't but a buddy of mine in Florida can and he uses the same exact Thetis version that I do (except that his works in P2, but I don't think that has anything do with this).
Richie:
Ditto above.....my buddy told me that when the mouse cursor morphs into a double arrow line I can drag the TX band-width by clicking the left mouse button and then just drag the bandwidth out. This, just to experiment rather than save anything necessarily. He did it on the fly while we were in contact the other day and I just tried to do the same.....
Thanks again for the feedback!
JJ
NI2M
PC: 8 Core i7-10700 CPU @ 2.90GHz, NVMe SK Hynix 512 GB SSD, 32GB RAM
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Re: Can't adjust TX bandwidth using mouse
JJ4SDR wrote:Gary, Richie,
Gary:
I can't but a buddy of mine in Florida can and he uses the same exact Thetis version that I do (except that his works in P2, but I don't think that has anything do with this).
Richie:
Ditto above.....my buddy told me that when the mouse cursor morphs into a double arrow line I can drag the TX band-width by clicking the left mouse button and then just drag the bandwidth out. This, just to experiment rather than save anything necessarily. He did it on the fly while we were in contact the other day and I just tried to do the same.....
Thanks again for the feedback!
JJ
NI2M
You tried while TX'ing? As Richie states it only works while in TX and even so there apparently are issue. Your screenshot shows you in receive so just wanted to make sure this was clear.
Cory K9CDR
Re: Can't adjust TX bandwidth using mouse
As Richie wrote, there are some issues with it. I can report that it doesn't work for me here, I.e. I cannot adjust the TX passband graphically when in transmit.
What I normally do is turn on the TXFL lines and then use the TX passband controls to adjust my TX bandwidth until the lines match up with the bandwidth of the others is the QSO.
What I normally do is turn on the TXFL lines and then use the TX passband controls to adjust my TX bandwidth until the lines match up with the bandwidth of the others is the QSO.
Re: Can't adjust TX bandwidth using mouse
yeah it is totally broken atm. I will look at it at some point.
Richie - MW0LGE - https://www.qrz.com/db/mw0lge
Latest Release [2.10.3.5] : https://github.com/ramdor/Thetis/releases/tag/v2.10.3.5
Latest Work In Progress : https://github.com/ramdor/Thetis/releas ... .3.6-dev_2
Latest Release [2.10.3.5] : https://github.com/ramdor/Thetis/releases/tag/v2.10.3.5
Latest Work In Progress : https://github.com/ramdor/Thetis/releas ... .3.6-dev_2
Re: Can't adjust TX bandwidth using mouse
Cory,
Yes, I did try dragging the TX bandwidth out while in TX mode. Again, my buddy was able to do just that.....
Best!
Juha,
NI2M
Yes, I did try dragging the TX bandwidth out while in TX mode. Again, my buddy was able to do just that.....
Best!
Juha,
NI2M
PC: 8 Core i7-10700 CPU @ 2.90GHz, NVMe SK Hynix 512 GB SSD, 32GB RAM
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Re: Can't adjust TX bandwidth using mouse
Maybe I'm premature with my question, When the TX bandwidth is adjusted with the mouse, is the adjusted bandwidth supposed to be retained the next transmissions?
Is this one of the things that's broken?
Is this one of the things that's broken?
73
Ruben
NB4R
Apache-Labs Anan 7000DLE MKII Black -- Thetis 2.10.3.6 dev_2 -- Windows 11
Ruben
NB4R
Apache-Labs Anan 7000DLE MKII Black -- Thetis 2.10.3.6 dev_2 -- Windows 11
Re: Can't adjust TX bandwidth using mouse
IIRC this used to work, and maybe still does in PowerSDR mRX. Doing this was no different than using the numeric controls. It does not currently work in Thetis.
Does that clear up any confusion?
Does that clear up any confusion?
Re: Can't adjust TX bandwidth using mouse
It clears it up for me. Thanks for the information Scott!
73
Ruben
NB4R
Apache-Labs Anan 7000DLE MKII Black -- Thetis 2.10.3.6 dev_2 -- Windows 11
Ruben
NB4R
Apache-Labs Anan 7000DLE MKII Black -- Thetis 2.10.3.6 dev_2 -- Windows 11
Re: Can't adjust TX bandwidth using mouse
I guess I could always get a MIDI controller and assign the TX bandwidth control to one of the sliders or knobs on the MIDI. Been thinking of going this route any way to put some phyusical wheels,knobs and sliders to the radio.
73 de Juha
NI2M
73 de Juha
NI2M
PC: 8 Core i7-10700 CPU @ 2.90GHz, NVMe SK Hynix 512 GB SSD, 32GB RAM
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Re: Can't adjust TX bandwidth using mouse
Hi, currently TX low/high filter can only be assigned to a wheel.
I never tried if it works with a knob or slider, but don't be disappointed if it doesn't work.
r/Leon
I never tried if it works with a knob or slider, but don't be disappointed if it doesn't work.
r/Leon
73 PD3LK Leon
Re: Can't adjust TX bandwidth using mouse
Hi Leon,
That's odd. Perhaps it depends on the MIDI controller you are using? Which one do you have?
Best!
Juha
NI2M
That's odd. Perhaps it depends on the MIDI controller you are using? Which one do you have?
Best!
Juha
NI2M
PC: 8 Core i7-10700 CPU @ 2.90GHz, NVMe SK Hynix 512 GB SSD, 32GB RAM
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Re: Can't adjust TX bandwidth using mouse
Hi, i'm using a DJControl Compact but this is a Thetis limit/shortcoming, not the controller. (look at the list of useable midi commands in Thetis)
r/Leon
r/Leon
73 PD3LK Leon
Re: Can't adjust TX bandwidth using mouse
Got it Leon!
Thanks.
NI2M
Thanks.
NI2M
PC: 8 Core i7-10700 CPU @ 2.90GHz, NVMe SK Hynix 512 GB SSD, 32GB RAM
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18
Windows 10 Home, Version 22H2
Thetis v2.10.4.3 x64
Protocol 2 v2.1.18