Thetis v2.10.3.5 final release

[Tony EI7BMB]

Ah, thanks for that Richie

Anyone notice that NB stays on during TX ?

It turns off during TX only if DUP is on

[W1RHS]

Hi Richie,

I am running Thetis v2.10.3.5 Pre-Release 3. I have it configured to prevent Tx on non-Ham freqs in the US. (Extended not checked in Setup). It works as expected with one minor thing.

If I Tx with the Thetis MOX button or the spacebar, I get the pop warning window, I close the window and Thetis continues.

If I Tx using my CMD-PL1 midi controller mapped key, I get the popup warning window, I close the window, and Thetis powers off. The Thetis power button goes off. I have to press power again in Thetis to continue.

It's not a big deal but it seemed inconsistent to me.

Thanks for the great work you do for all of us!

Rick, W1RHS

[f6ctt]

Hello

With my Anan 200 D, the VAC1 doesn't work : no audio

back to the version 2.10.3.4 : audio is OK

73 Joseph F6CTT

Hello again

If I uninstall version 2.10.3.4 and install today's version 2.10.3.5 prerelease-4, VAC1 does not work (no audio in the headset).

After doing a new installation of today's prerelease version-4 (I deleted the OpenHPSDR directory to do so), VAC1 works again.

73 Joseph

[K1LSB]

Hello again

If I uninstall version 2.10.3.4 and install today's version 2.10.3.5 prerelease-4, VAC1 does not work (no audio in the headset).

After doing a new installation of today's prerelease version-4 (I deleted the OpenHPSDR directory to do so), VAC1 works again.

73 Joseph

Where was there any notice of a new 2.10.3.5 pre-release 4 posted?

Thanks,
Mark

[ramdor]

Where was there any notice of a new 2.10.3.5 pre-release 4 posted?

there wasn't one this time Mark

[ramdor]

If I Tx using my CMD-PL1 midi controller mapped key, I get the popup warning window, I close the window, and Thetis powers off. The Thetis power button goes off. I have to press power again in Thetis to continue.

The code turns off the radio if a cat based ptt/mox fails (midi uses cat functions/calls). It fails due to being out of band and then it just powers off. I checked back to March 2017 and the code is there, and like 99% of the strange things that go on in the spaghetti, there are no comments as to why.

[w-u-2-o]

The code turns off the radio if a cat based ptt/mox fails (midi uses cat functions/calls). It fails due to being out of band and then it just powers off. I checked back to March 2017 and the code is there, and like 99% of the strange things that go on in the spaghetti, there are no comments as to why.

This has always seemed to be a rather overly draconian response to an attempt to transmit out of band. It would be vastly preferable if the software merely refused to TX. A pop-up message isn't even required.

[w9mdb]

Seems to me the problem might be that you really don't know if the PTT worked.
If the PTT was never sent that would fix that problem though you'd still want some sort of warning...otherwise people are wondering why PTT doesn't work. A temporary popup of "Frequency X.XXMHz is out of band -- PTT aborted" should do.
Still same behavior though if PTT is sent and fails for any reason you don't know the state of the rig so power off is the safety position.

[Mike_N1JEZ]

I must be missing something, but I can't find the link for the download for pre-release 4... other than https://github.com/ramdor/Thetis/releas ... -release-4

Mike

[NC3Z]

I must be missing something, but I can't find the link for the download for pre-release 4.
Mike

Have you scrolled to the bottom of the page?

Screenshot 2023-12-15 065658.jpg (126.26 KiB) Viewed 73207 times

[Mike_N1JEZ]

Boy do I feel foolish. I could have sworn I scrolled down to the bottom....
Tnx, Mike

[Tony EI7BMB]

Took me a while too Mike

Boy do I feel foolish. I could have sworn I scrolled down to the bottom....
Tnx, Mike

[n2gq]

When using panafall and I try to expand the waterfall all the way up Thetis exits. Also happened once when scrolling the frequency bar on top of spectrum display.

Radio is 7000del mkIII
Firmware 2.1.12
Running W11 7800xt video card latest amd drivers.
Video below.


https://youtu.be/cuChn1B5Rno

[oe3ide]

When using panafall and I try to expand the waterfall all the way up Thetis exits. Also happened once when scrolling the frequency bar on top of spectrum display.

Radio is 7000del mkIII
Firmware 2.1.12
Running W11 7800xt video card latest amd drivers.
Video below.


https://youtu.be/cuChn1B5Rno

video unavailble (I guess private)

[n2gq]

When using panafall and I try to expand the waterfall all the way up Thetis exits. Also happened once when scrolling the frequency bar on top of spectrum display.

Radio is 7000del mkIII
Firmware 2.1.12
Running W11 7800xt video card latest amd drivers.
Video below.


https://youtu.be/cuChn1B5Rno

video unavailble (I guess private)

Video should be available now.

[ramdor]

When using panafall and I try to expand the waterfall all the way up Thetis exits. Also happened once when scrolling the frequency bar on top of spectrum display.

can you send me this zip. My email is over on qrz. Cheers.

zip.jpg (21.55 KiB) Viewed 73044 times

[n2gq]

When using panafall and I try to expand the waterfall all the way up Thetis exits. Also happened once when scrolling the frequency bar on top of spectrum display.

can you send me this zip. My email is over on qrz. Cheers.

zip.jpg

Okay on it's way.

[vk1hx]

When using panafall and I try to expand the waterfall all the way up Thetis exits. Also happened once when scrolling the frequency bar on top of spectrum display.

Radio is 7000del mkIII
Firmware 2.1.12
Running W11 7800xt video card latest amd drivers.
Video below.


https://youtu.be/cuChn1B5Rno

I am not experiencing this reported behavior. Tested while running Thetis powered on and off.

Tested on Microsoft Windows 11 (Pro and Enterprise 23H2)

[ramdor]

Okay on it's way.

Sadly nothing of relevance in the errorlog.txt file. I ran up your db and spent about 5 mins slamming the splitter bar from top to bottom, dragging the splitter bar, and no issue.

If you can get it to repeatedly happen on demand, try closing down all other programs and clearing out everything from the the system tray icons.

[w9mdb]

It may matter how the monitors are setup assuming there are at least two monitors (which I suspect there is).

Mine are "extended" with the #1 screen top and #2 on the bottom and I can't duplicate this problem.
But if you put #1 on the bottom and #2 on the top the offset numbers are negative -- perhaps that's the problem?

Mike W9MDB

[n2gq]

Okay on it's way.

Sadly nothing of relevance in the errorlog.txt file. I ran up your db and spent about 5 mins slamming the splitter bar from top to bottom, dragging the splitter bar, and no issue.

If you can get it to repeatedly happen on demand, try closing down all other programs and clearing out everything from the the system tray icons.

Okay will try clearing programs from the tray. Will let you know how that turns out.

[n2gq]

Okay on it's way.

Sadly nothing of relevance in the errorlog.txt file. I ran up your db and spent about 5 mins slamming the splitter bar from top to bottom, dragging the splitter bar, and no issue.

If you can get it to repeatedly happen on demand, try closing down all other programs and clearing out everything from the the system tray icons.

Okay I cleared as many as I could programs from system tray but same thing was happening. I then reduced display resolution down to 1080p from 2160 and I could not trigger the exit of thetis. I dragged multiple times and nothing happens. Will continue checking. Also exits at 1440 resolution.

[n2gq]

Okay on it's way.

Sadly nothing of relevance in the errorlog.txt file. I ran up your db and spent about 5 mins slamming the splitter bar from top to bottom, dragging the splitter bar, and no issue.

If you can get it to repeatedly happen on demand, try closing down all other programs and clearing out everything from the the system tray icons.

Okay I cleared as many as I could programs from system tray but same thing was happening. I then reduced display resolution down to 1080p from 2160 and I could not trigger the exit of thetis. I dragged multiple times and nothing happens. Will continue checking. Also exits at 1440 resolution.

At 2160 or 4k resolution and the recommended scale of 150% thetis exits if I drag up the waterfall. But if I move the scale to 175 and above it does not exit.

Also got this window one time. Picture attached.

Thetis crash20231216_111028.jpg (689.27 KiB) Viewed 72578 times

[w-u-2-o]

I'm running 4K resolution and cannot duplicate this problem.

Edited to add: also running 150% scaling.

I know this is a somewhat trite suggestion, but have you tried updating your video drivers?

[n2gq]

I'm running 4K resolution and cannot duplicate this problem.

Edited to add: also running 150% scaling.

I know this is a somewhat trite suggestion, but have you tried updating your video drivers?

Yes, just the day before I updated the Radeon drivers.

[n2gq]

Okay I am using a display port cable to my monitor. And when I use an HDMI cable it does not occur.

Talked a bit soon, it still occurs but takes a bit longer.

[ramdor]

Yes, just the day before I updated the Radeon drivers.

was it an issue before you updated them?

[n2gq]

Yes, just the day before I updated the Radeon drivers.

was it an issue before you updated them?

Don't know but going back one to see if it was an issue. Get back to you.

[n2gq]

Yes, just the day before I updated the Radeon drivers.

was it an issue before you updated them?

Not sure as I don't use the waterfall in full screen all the time .

Don't know but going back one to see if it was an issue. Get back to you.

I went back as far as 2.10.0 and it did the same thing.

Going to try a different driver for gpu.

[ramdor]

updated to pre-release-5 and hopefully the last pre-release