ea3aqr wrote:21D3:
USB/LSB problem soved, but unfortunately, at startup, the filter is always changed to a 2.9k width filter.
Is that the filter assigned to a the current stack entry or last used mode?
R.
ea3aqr wrote:21D3:
USB/LSB problem soved, but unfortunately, at startup, the filter is always changed to a 2.9k width filter.
ramdor wrote:21d3 is up there
Couple of fixes for 21d3, and some changes, please see the list. I just ran some testing on PS on the 7000 here, P2, and seemed fine with default DDC/ADC assignments, and with ADC set at 0 for both DDC2 + 3. There may be some issue if both assigned to ADC1, testing continues.
Also, note there is WIP for notches in transverter bands atm. Still in a state of flux.
R.
ramdor wrote:ea3aqr wrote:21D3:
USB/LSB problem soved, but unfortunately, at startup, the filter is always changed to a 2.9k width filter.
Is that the filter assigned to a the current stack entry or last used mode?
R.
ea3aqr wrote:ramdor wrote:ea3aqr wrote:21D3:
USB/LSB problem soved, but unfortunately, at startup, the filter is always changed to a 2.9k width filter.
Is that the filter assigned to a the current stack entry or last used mode?
R.
Nope, I never use 2.9k filter, all my stack entries and last used mode are at 2.4k.
When Thetis loads it shows the last used band and always a 2.9k filter.
EDIT: When I click on "band" it cycles thru my band stacks and the correct 2.4k filter is applied on first click. I don't know where the 2.9k filter is coming from...
ea3aqr wrote:ramdor wrote:ea3aqr wrote:21D3:
USB/LSB problem soved, but unfortunately, at startup, the filter is always changed to a 2.9k width filter.
Is that the filter assigned to a the current stack entry or last used mode?
R.
Nope, I never use 2.9k filter, all my stack entries and last used mode are at 2.4k.
When Thetis loads it shows the last used band and always a 2.9k filter.
EDIT: When I click on "band" it cycles thru my band stacks and the correct 2.4k filter is applied on first click. I don't know where the 2.9k filter is coming from...
DO2ZA Erwin wrote:DO2ZA Erwin wrote:Hi Ritchie,
21d2 is working fine here, TRX and FW see in my Signature.
PS is working perfekt here, no Problems with it, picking the Signal with ext. Sampler behind my Amplifier.
73 Erwin
Okay, did a test with RX S-ATT 6 dB, Pure Signal work perfekt, but when back to RX i have higher Noise (goes up with 6 dB) on the Spectrum
and on the Audio and 6 dB more on the S-Meter.
Without RX ATT this will not happen.
ramdor wrote:ok you think this might a problem at the import stage? I will go check in there to see if existing filters are copied over. I wonder if ea3aqr did that this time as well? Although, tbh, the old tables no longer exist if importing from anything 21d onwards.
Also, I missed the damn flat style for the vacstereo.....
Richie.
ramdor wrote:Just a status update. I going MIA for a couple of days to get some other stuff done around here irl.
If there are any big problems uncovered I will look at another quick 21d patch, but for the moment, I would like the dust to settle and work through anything that crops up to be included/fixed in 21e. P1 needs investigating and testing, I have not done that yet, later in the week.
R.
ramdor wrote:ok you think this might a problem at the import stage? I will go check in there to see if existing filters are copied over. I wonder if ea3aqr did that this time as well? Although, tbh, the old tables no longer exist if importing from anything 21d onwards.
Also, I missed the damn flat style for the vacstereo.....
Richie.
Helmut wrote:Hello Ernst,
can you test for me predistortion without the Gemini - solo - abt 20W running Vers 21D3
I normaly do not use the S-ATT on receive - have ATT in setup so that in OPTIONS the Step Attenuators are unchecked.
Then in Ant/Filters uncheck RX BYPASS and check ATT on TX with 31dB
If you now press 2TON the ATT on TX sould go to abt 12dB and Predistortion is here abt 60dB IMD
Then press MOX or the Mike-Ptt the ATT on TX goes to 31dB or to 0dB and Predistortion does not come back to 12dB to work proper ??
73 Helmut oe9eri
ramdor wrote:Just a status update. I going MIA for a couple of days to get some other stuff done around here irl.
If there are any big problems uncovered I will look at another quick 21d patch, but for the moment, I would like the dust to settle and work through anything that crops up to be included/fixed in 21e. P1 needs investigating and testing, I have not done that yet, later in the week.
R.
DO2ZA Erwin wrote:DO2ZA Erwin wrote:DO2ZA Erwin wrote:Hi Ritchie,
21d2 is working fine here, TRX and FW see in my Signature.
PS is working perfekt here, no Problems with it, picking the Signal with ext. Sampler behind my Amplifier.
73 Erwin
Okay, did a test with RX S-ATT 6 dB, Pure Signal work perfekt, but when back to RX i have higher Noise (goes up with 6 dB) on the Spectrum
and on the Audio and 6 dB more on the S-Meter.
Without RX ATT this will not happen.
This is happend also in 21d3 Edit: in 2.8.11 this was not, when given 6 dB Rx-ATT the Gain Line goes up, after TX all stays like before
Edit: Info: with a fresh Database testet, no changes
73 Erwin
dl5tt wrote:Hi Richie,
concerning the (my) attenuator problem (in normal operation).
After the information from OE3IDE I tried to verify his results, but with no success.
So I did a Database reset....and: Now it works. If I reload my old database, the problem is again existent. So the problem must be in my database.
I have no idea what kind of parameters are in the database, which affect the attenuator function.
Do you have any hints which tags are relevant for the attenuator function?
Sorry for wasting your time with this issue.
It seems to me, that I have to configure a new database.
73 de Josef
ea3aqr wrote:Richie and Ernst,
Yes, I copied 21d3 files and started Thetis holding CTRL key.
Richie, sending my database to your QRZ e-mail in just a minute!
Thanks
DO2ZA Erwin wrote:DO2ZA Erwin wrote:DO2ZA Erwin wrote:
Okay, did a test with RX S-ATT 6 dB, Pure Signal work perfekt, but when back to RX i have higher Noise (goes up with 6 dB) on the Spectrum
and on the Audio and 6 dB more on the S-Meter.
Without RX ATT this will not happen.
This is happend also in 21d3 Edit: in 2.8.11 this was not, when given 6 dB Rx-ATT the Gain Line goes up, after TX all stays like before
Edit: Info: with a fresh Database testet, no changes
73 Erwin
Update: Now with d3 i have testet again. The Prob. with the RX-Att is only with the S-ATT, with the normal ATT coming back to RX it is all okay.
73 Erwin
PD3LK wrote:Hi, i'm not sure if this has worked before.... can't scroll this digit with the mouse wheel.
regards, Leon
ramdor wrote:Well it seems that the adc linking has caused some issues, so I will drop all that for now until I can get to the bottom of it later in the week.
Also, I have found the problem with the bandstack thanks to Jordi. A different vfob filter would cause an update to vfoa filter, not a good thing
Should be an update 21d4 sometime later today.
R.