VA2EY wrote:Works with VAC only
Michel
will add option for now enable/disable the functionality as a stop gap
Richie.
VA2EY wrote:Works with VAC only
Michel
w-u-2-o wrote:The change from milliseconds to frames on the waterfall update rate threw me for a minute! I couldn't figure out why it was going so slooooooow
VA2EY wrote:Hmmm ...
with the new box no change from -70dB to + 70dB, only affects the VAC
test with old database and reset
Michel
VA2EY wrote:Hmmm ...
with the new box no change from -70dB to + 70dB, only affects the VAC
test with old database and reset
Michel
ramdor wrote:w-u-2-o wrote:The change from milliseconds to frames on the waterfall update rate threw me for a minute! I couldn't figure out why it was going so slooooooow
hah yes, bit slow with high numbers. Was thinking about going back to ms and do the reverse calculation, and round to frame rate interval, but left as is for now.
Richie.
DL8LAQ wrote:Hi Richie!
It seems that the MIC gain is not adjustable since versions higher than b_2. I am back to b_2 and MIC gain is adjustable.
I used a clean database to check that!
ramdor wrote:DL8LAQ wrote:
Odd, fine here, though I dont use direct connect. Not done anything to the mic gain code either. hmm. You are replacing all the files not just thetis.exe right? I will try a fresh db here as well, but would expect it to be ok.
Richie.
ramdor wrote:ok, 20 mins, think I have found the problem.
Richie.
ramdor wrote:Michel, Norbert and those testing mic gain issues, please try this test version :
https://www.dropbox.com/s/h2x2ug3wodgde ... t.zip?dl=0
If ok I will release a b6 with the changes.
Richie.
ramdor wrote:Michel, Norbert and those testing mic gain issues, please try this test version :
https://www.dropbox.com/s/h2x2ug3wodgde ... t.zip?dl=0
If ok I will release a b6 with the changes.
Richie.
DL8LAQ wrote:Richie, did u change something around the VAC1 TXGain? I am almost sure that last month when I used digital modes via VAC the VAC1 TXGain was set to 0, but today I tried Thetis for MSK144 (meteorscatter) I had to turn up the gain to >30dB to get a signal strong enough to drive my PA.
Thanks again for all, Richie Have a good night...
VA2EY wrote:YES!!
mic gain works and TX gain Wave menu also
you are the best. now the beer ...
KA1GXR wrote:Can anyone else duplicate this? Using 200D Firmware 1.8. Thetis 2.69 B1 or B5:
If QSK is turned on Tx power goes to whichever RX antenna is selected 1,2, or 3 even with Ant 1 checked as TX and check boxes
under ANT 2 and 3 for do not transmit on those antennas.
I duplicated on a Windows 10 and Widows 7 different desktop PC. Hope this is not intended operation. I only use CW for TX power calibrate and tuning normally.
Tom
KA1GXR
ramdor wrote:UPDATE
Hi all,
An update to fix some issues with mic gain, especially if you don't use VAC.
Please try : https://www.dropbox.com/s/z4d5bx6nhhbgp ... 6.zip?dl=0
Full change log list : https://docs.google.com/document/d/1xh4 ... 5-ibeIBt_k
73 Richie.
(11/19/19) b6
-fix: mic gain issue when no vac used, introduced with changes in b5_3
NL7F wrote:
With b6 waterfall is now inoperative on my 200D
regards, NL7F
KA1GXR wrote:If QSK is turned on Tx power goes to whichever RX antenna is selected 1,2, or 3 even with Ant 1 checked as TX and check boxes
under ANT 2 and 3 for do not transmit on those antennas.