No Output power when WSJT-X Tune button is activated
Posted: Thu Jun 16, 2022 10:23 pm
THETIS Crashed during an FT8 Contact and no longer functions with WSJT-X
Postby Dick » Thu Jun 16, 2022 3:21 pm
Greetings All
After several Issues (blank Panafall screen after upgrading to THETIS v2.9.0.6 x64) were solved with great mentoring, I was successfully running THETIS with WSJT-X (v2.5.4 ), JTAlert (v2.51.3 ), DXKeeper (v16.4.5 ) . After ten-plus successful contacts made and logged, a pop-up screen appeared saying THETIS had stopped working.
I finally had to access TASK MANAGER to close-out THETIS. I restarted THETIS and clicked on the power button in the T-Main-screen. Another pop-up asked if the ANAN-200D was connected or powered up - it was. I had to power-cycle the 200D after which THETIS connected to the SDR and displayed signals normally in the Panafall display.
Next I restarted WSJT-X and tried contacting someone (decodes signals fine) but now, there was zero output power when the 200D was in TX mode. I had made no changes to the setup of WSJT-X or in THETIS (or anywhere!) since it had last been working. This ZERO output condition started immediately after the first THETIS crash.
Under these conditions I do see RF output when the THETIS "Tune" button is activated.
Seems like I'm in a wack-a-mole event getting one thing after another to work correctly but the damn Mole is winning !!
My system setup is as follows:
- DELL E6510 laptop running W-7 64-bit OS (8GB of added RAM)
- ANAN-200D (in day-one shipment status)
-THETIS v2.9.0.6
- WSJT-X v2.5.4
- DXKeeper v16.4.5
- LOTW (so far no problems here!)
Speeds :
- Internet 58.6Mbps
- 100Mbps LAN (Intel (R) 82577LM GigaBit Network (for connection to ANAN-200D direct Ethernet connection)
Hopefully someone has an answer to this problem.
73 Dick/w7wkr at CN98pi
Postby Dick » Thu Jun 16, 2022 3:21 pm
Greetings All
After several Issues (blank Panafall screen after upgrading to THETIS v2.9.0.6 x64) were solved with great mentoring, I was successfully running THETIS with WSJT-X (v2.5.4 ), JTAlert (v2.51.3 ), DXKeeper (v16.4.5 ) . After ten-plus successful contacts made and logged, a pop-up screen appeared saying THETIS had stopped working.
I finally had to access TASK MANAGER to close-out THETIS. I restarted THETIS and clicked on the power button in the T-Main-screen. Another pop-up asked if the ANAN-200D was connected or powered up - it was. I had to power-cycle the 200D after which THETIS connected to the SDR and displayed signals normally in the Panafall display.
Next I restarted WSJT-X and tried contacting someone (decodes signals fine) but now, there was zero output power when the 200D was in TX mode. I had made no changes to the setup of WSJT-X or in THETIS (or anywhere!) since it had last been working. This ZERO output condition started immediately after the first THETIS crash.
Under these conditions I do see RF output when the THETIS "Tune" button is activated.
Seems like I'm in a wack-a-mole event getting one thing after another to work correctly but the damn Mole is winning !!
My system setup is as follows:
- DELL E6510 laptop running W-7 64-bit OS (8GB of added RAM)
- ANAN-200D (in day-one shipment status)
-THETIS v2.9.0.6
- WSJT-X v2.5.4
- DXKeeper v16.4.5
- LOTW (so far no problems here!)
Speeds :
- Internet 58.6Mbps
- 100Mbps LAN (Intel (R) 82577LM GigaBit Network (for connection to ANAN-200D direct Ethernet connection)
Hopefully someone has an answer to this problem.
73 Dick/w7wkr at CN98pi