HI All
Just started to modify my own " basic_controller" made by John Melton g0orx/n6lyt but I need the CAT command for the RX2 AF: ??
...I know that "ZZAG" is master AF
73" OZ1CT Ben
RX1 AF: CAT command????
Re: RX1 AF: CAT command????
See this topic: viewtopic.php?f=16&t=2577&p=3827
The CATStructs.xml file appears in the similar directory under Thetis as well, if you are using Thetis.
The CATStructs.xml file appears in the similar directory under Thetis as well, if you are using Thetis.
Re: RX1 AF: CAT command????
Hi Scott
Yes I did see in the CATStructs.xml file in Thetis directory..... but there is nothing ....
so I still look for RX1 AF: but maybe there is no cat command ???
73" Ben
Yes I did see in the CATStructs.xml file in Thetis directory..... but there is nothing ....
so I still look for RX1 AF: but maybe there is no cat command ???
73" Ben
Re: RX1 AF: CAT command????
There are CAT commands for all audio levels. The problem is that they are poorly labeled/poorly named. I had to go into both the XML file and the Flex reference document and look through them for you.
In CATStructs.xml:
Master AF is called "extended AG Gain", ZZAG
RX1 AF is called "RX0 Gain", ZZLA
RX2 AF is called "RX2 audio level", ZZLE
There is also "RX1 Gain", ZZLC, which I think is for the main (RX1) sub-receiver.
You will have to test all of these to see what they really do. You can do this in Thetis by going to Setup > CAT Control > CAT > Test CAT Commands.
In CATStructs.xml:
Master AF is called "extended AG Gain", ZZAG
RX1 AF is called "RX0 Gain", ZZLA
RX2 AF is called "RX2 audio level", ZZLE
There is also "RX1 Gain", ZZLC, which I think is for the main (RX1) sub-receiver.
You will have to test all of these to see what they really do. You can do this in Thetis by going to Setup > CAT Control > CAT > Test CAT Commands.
-
- Posts: 225
- Joined: Mon Nov 11, 2019 7:39 pm
Re: RX1 AF: CAT command????
There is a CAT command reference guide in the Thetis documentation. https://github.com/TAPR/OpenHPSDR-Thetis/tree/master/Documentation/Radio
It isn't absolutely up to date but you are unlikely to encounter the newest CAT commands yet, I will ask Doug to add the newest one at a convenient point.
It isn't absolutely up to date but you are unlikely to encounter the newest CAT commands yet, I will ask Doug to add the newest one at a convenient point.
Laurence Barker G8NJJ
Re: RX1 AF: CAT command????
Hi All
Just what I need for my Cat-controller.... I am runnig it on a small Arduino Micro board....
hare is a picture where the SKF-ball bering encoder and enclosure will be put together
Just what I need for my Cat-controller.... I am runnig it on a small Arduino Micro board....
hare is a picture where the SKF-ball bering encoder and enclosure will be put together
- Attachments
-
- in the mittel of wheel a switch to press when AF is adjust.
- cat2.gif (197.15 KiB) Viewed 4105 times
-
- have to cut a hole in topcover, so only knop is out.
- cat1.gif (288.59 KiB) Viewed 4105 times