Just out of curiosity what do you plan to use those outputs for?

The pinout is here: https://apache-labs.com/community/viewtopic.php?f=35&t=2343 You can program the pins to work however you like in Setup > General > ANAN Control, and "Ext Control" must be enabled on that screen. Each output is basically an open drain FET switch to ground when assert...

GW0NTM wrote:Hi All

Does anyone know what input channels are being used by cmASIO? Is it mono from channel #1, or a mono combination of channels #1 and #2?

Thanks
Robin

Mono combination.

Full schematics for the 7000, 8000, Andromeda and G2 have not been cleared for public posting by Apache. However, in accordance with the open source hardware derivative works license clause, they will provide them direct to any owner on request. You will need to mail Apache.

I don't have a G2. However there have been a number of people who have had success with the balanced input (and a number of people who haven't ).

I would suggest trying the balanced TRS input on the back (it may be somewhat erroneously marked "XLR"). However, beware that that is the input to a high gain mic preamp and thus it would be prudent to go easy on levels at that input.

Sort of. Master AF will control the overall audio level for cmASIO. My recommendation would be to set RX1 and RX1 AF to maximum. This will achieve a proper and optimal 0dB audio level into digi mode software attached via VAC. Then use Master AF to adjust cmASIO audio level and which does not affect ...

Can cmASIO be used over the internet using remote desktop software? Not directly. You can pass it through Voicemeeter to one of your remote access app's. If you have more questions about remote op's please post them in the remote op's part of the forum: https://community.apache-labs.com/viewforum.p...

There's no setting on the various audio tabs that has any effect on cmASIO. It has nothing to do with VAC.

This is starting to sound like RFI. What happens on 80M if you run into a dummy load?

Short answer: make the filter length shorter in Setup > DSP > Options.

Pretty much everything you need to know is in this topic: viewtopic.php?f=9&t=4081

And I'm amazed that Thetis doesn't have built in buttons for programmable CAT macros. Not really amazed, of course... Consider that Thetis is fully open source and developed by volunteers doing it for the love of the hobby. Consider also that the number of folks who have done substantial work on it ...

That last post confused me for a while. There's no need to use rigctlcom for Winlink unless you have run out of serial CAT instances in Thetis. I.e. this approach does not eliminate the use of virtual serial connections where Winlink is concerned.

How are you starting VSPE right now? Does it load as a service, is it launched as a startup item, or is it launched from a script?

Thanks Scott - yes phantom power is on. Clearly a boom arm is now on my shopping list. If I shoot for ~ -3dB peaks on the MIC meter via the gain on the Motu (VAC TX gain at 0dB, TX eq off), I do see some minor clipping on the Motu display on the pops and whistles. Maybe thats ok? I'm not Scott but ...

Richie can't fix that problem. It could be fixed in VSPE if Eterlogic implemented a retry process on that type of port.

Create a script that starts things in the correct order and with any necessary delays

Guitar Center is the proverbial candy store! [Obi-Wan] One must be cautious with one's wallet when in Guitar Center [/Obi-Wan] :D You are lucky to have one near you. The closest to me is 90 minutes away. I'm shocked that the salesman was disparaging the Behringer. I was using a UMC202 before I got t...

I'm using a Behringer B1 large diameter condenser into a Presonus Studio 192 interface. It is twice as sensitive as the CL7a, 20mv/Pa vs 10mv/Pa, and I don't have any objectionable room noise. Your gain settings seem insanely high across the board. The Motu gain should not be anywhere close to max. ...

See also this topic: https://community.apache-labs.com/viewtopic.php?f=22&t=4249

Damn! I totally forgot about that feature of VSPE, and I'm a long time proponent and user of VSPE

Well done!

Have you reviewed the manual? This does not sound like a networking problem. The 0.0.0.0 nonsense is for the FPGA-based models, not the Pi based model. You are working with Raspian Linux where networking is concerned. Use the usual Linux commands on the G2 desktop to ensure it is set the way you wan...

Great idea, Mike!

Thetis TCP/IP <--> rigctlcom <--> VSPE port pair <--> Some other application

Go to Setup > DSP > Options.

If they are not already set like this, try changing filter type to linear phase and filter size to 1024.

I have used the hotsample.exe. It says "RODECaster" and when I add the string to registry, then reboot thetis; it says issue starting cmASIO check driver name in registry. Hi OM, Can you please send me (by PM or email) the complete output from the hostsample.exe utility? Since the RODECas...

@W4WMT

Bryan--would you consider adding a feature to allow cmASIO to obtain the buffer setting from the driver rather than mandating a fixed buffer of 64?

I changed the name of this topic to be more generic, and also made it a sticky for now since it is getting a lot of traction.

Great video, Richie! A couple of comments/thoughts... The primary reason for this is not latency per se (although that is a definite benefit!), but for people who are in a fully virtualized environment (radio as a black box with only an Ethernet connection to the hardware--ANAN or otherwise) to be a...

Try updating to the latest release, 2.10.3.5 final just to be sure that's not the problem.

My bad, I meant "lockmode", sorry!

Locking this topic, please continue on in the 2.10.3.5 topic!

cmASIO posts moved to the main cmASIO discussion topic:

viewtopic.php?f=13&t=4923&start=90