old i5 and anan was conneted to router. new i7 has 2 lan so is connected 1 lan to router and 1 to anan. following w1aex setup. so the kind of lan used don't change the result....for the problem i have. Generally if a 2 lan conncetion is faster/usefull i cannot judge for the moment Are you saying tha...

i was using anan 7000 in this days with a mini pc , i work fine for me and have this setup i5/8gb/ssd/100 bit lan trought router pc. All was ok. Then i also setup my laptop with same configuration. may be is just a little bit slower but was all ok. Then i bought a new computer i78/8gb/ssd/ 2 gigabit...

i have anan 7000 using ps-a software now. but lookig for a coupler any suggestions? i have found this one : https://www.hamradio.com/detail.cfm?pid=H0-015644 in the past i alsofound another one made by an ham in us but don’t remember any more the call/webisite Or other suggestions? I will use mainly...

i have tryend too, but when i go on VFO B, and try to Tx still anan enter in split mode. also what you see in VFOB are the rx2 signals . you can on only tx on one of the 2 frq of multy rx of VFOA. so if you chatch a signal in in VFOB how can tx in that freq? sorry but still not get, also from the yu...

only one more question on the tx part. on the setting i have , i did't select but have s-attenuator that is activated when when i go in tx.

normally in general->Options is not enabled. but when go in tx is activated with -6db att.

thanks

i have anan 7000 an i want understend the below questions plus what is the LNA 15/12/10 button? 2. When ALEX is ON, there is a hard-coded table in firmware that looks at the frequency of VFO-A and sets the preselection BPF in accordance with the frequency. If both RX1 and RX2 are being fed by ADC1 t...

While you can run PureSignal and an external amplifier without an external coupler, in such a case you will only be linearizing the radio, not the external amplifier. this i know. next step will be use external coupler. Without the external amplifier in line, and with PureSignal OFF, can you achiev...

My apologies, but I am having a difficult time reading your English :( sorry will try to explain better I moved this topic because it has nothing to do with firmware, and it has nothing to do with the 7000 specifically. If I'm reading things correctly it seems like a PureSignal problem. more then p...

I was setting the TX for pure signal. all was fine with rtx. then i connect the pa and check als signal with pa. all was fine. i made a qso. during qso i saw that pure signal green light/feedback and the wave form of my tx was changing. also i saw that final power of amp when down. i set them max po...

clear and noted now. one more question. on RX2 i don'see and MOX button, so to go on tx there can only change focus from tx on vfo A to vfo B(while rx2 is activated) right? any short cut? if don't want do it with mouse? thanks in advance Skinning does not affect the location or arrangement of button...

ok NOTED, all Clear thanks thanks The filename and the reported version number do not match. This is a known bug. You are running the latest. The speaker output jack on the back is the output of a 3 WATT AUDIO POWER AMPLIFIER. DO NOT USE IT WITH A POWERED SPEAKER. Also, the wiring of the speaker jac...

yes i know about hte RX2 button. what i did't know and the problem i had was becouse was selected the SD (stereo Diversity) funcion, so i could't switch band. now i deselect and is ok. about the buttons below your Yellow line is more clear now. but still i don't understand why are there. there are a...

What setup can enable my ADC2 using RX2 bnc to monitor a second band while i transmit ? In a contest, for example, transmit in band A and continue receiving in band B to search for multipliers. I have Anan 100D and not sure about the version of the RF board. is this really possible with anan 7000? ...

Perhaps the most mundane thing to do with ADC2 is to use it to monitor a second band using a separate antenna. You can also use it with different antennas to effect amplitude, polarization and other forms of non-coherent, spatial diversity. 73, Scott Activated the RX2 and correct antenna connected:...

bought my anan on jan 2019. received with firmware 2.3 downloaded and installed this new suggested update. 1) file name is metis_orion_mkii_v2.6rbf - Once updated powersdr setting show ID: orionMKII Ver:2.4!!! why? 2) first impression: i had volume to 0 and an amplified speaker connected directly to...

yes was that. i switch it back and all work fine. i did't notice before, thanks a lot. You may have accidentally moved the Bootloader switch, located on the bottom of the 7000, to the Bootloader mode. The radio chooses the operating mode, Normal or Bootloader, during power up based on the position o...

no.

seams no ip address is generated.

w9mdb wrote:Can you ping the radio?
de Mike W9MDB

Just bought 7000DLE. connected to my lan and work fine on first attempt. i have packet and moved anan inb my suitcase. connected in the new location to locan lan and pc. Setting are the same , but i cannot find the 7000 in my lan or using the powrsdr mrx. whe i try to power on i have an error that s...