Search found 5576 matches
- Sat Feb 03, 2024 10:27 pm
- Forum: Upgrading/Downgrading
- Topic: Is Bootloader working OK for people who are running Windows 11?
- Replies: 23
- Views: 7603
Re: Is Bootloader working OK for people who are running Windows 11?
Two NICs? Try disabling the NIC you don't need prior to running Bootloader (Settings > Network & Internet > Change adapter options, right click on the adapter in question). You won't break anything by doing this, you can simply enable it again when you are done.
- Thu Feb 01, 2024 5:53 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: Firmware fix for RF appearing on RX only ports
- Replies: 77
- Views: 8437
Re: Firmware fix for RF appearing on RX only ports
I just istalled Firmware 2 12.2.1A in my 100D first edition. Now I have "sequence error 264 / 265 (DDC2 Mic)" and an distordet audio. Database reset has no effect. Any idea? Yes. Unfortunately that firmware version is not closing timing on your hardware. You will have to petition Rick for...
- Thu Feb 01, 2024 11:48 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Log4OM not receiving CW mode info
- Replies: 3
- Views: 1165
Re: Log4OM not receiving CW mode info
I've recently started using CMaudio with a Behringer UMC202HD and ASIO driver. I also know that I no longer have cw sidetone. Could this CW mode info not being sent to Log4OM be a side effect of CMaudio? No, it's not a side effect of CMaudio. There is no CW sidetone available when VAC or CMaudio is...
- Thu Feb 01, 2024 11:41 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Log4OM not receiving CW mode info
- Replies: 3
- Views: 1165
Re: Log4OM not receiving CW mode info
Disclaimer: I don't use Log4OM. TCI is not 100% implemented in Thetis. Try using the network hamlib method instead. See page 23 in the Log4OM manual and also this link: https://community.apache-labs.com/viewtopic.php?f=22&t=4249&p=28188 If Log4OM is built using the latest version of hamlib y...
- Thu Feb 01, 2024 11:31 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: Firmware fix for RF appearing on RX only ports
- Replies: 77
- Views: 8437
Re: Firmware fix for RF appearing on RX only ports
Would it be a good idea to install this new firmware for my 8000DLE even if I don't do CW? I haven't encountered any of the problems mentioned on Github. But, since I only use phone, I don't know if the problem would cause problems with other modes and possibly do some damage to my radio. James WD5...
- Wed Jan 31, 2024 5:55 pm
- Forum: Thetis
- Topic: 700DLE/Thetis ext 10 Mhz sorce( AND) correction factor?
- Replies: 12
- Views: 2119
Re: 700DLE/Thetis ext 10 Mhz sorce( AND) correction factor?
So what's different about 2.2.2b? In this case it's just two different compiles of the same code. The problem with the free Quartus Lite FPGA development environment is that it is impossible to lock down the timing (aka incremental build, aka floor planning). So every compile results in slightly di...
- Wed Jan 31, 2024 3:49 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: DAW - Anan connection via VoiceMeeter Banana
- Replies: 13
- Views: 1480
Re: DAW - Anan connection via VoiceMeeter Banana
It's definitely working. Steve K1GMM had a RACK rack connected to audio devices and sent the signal to Thetis via the audio card via Banana. In the audio tab he selected Asio - virtual cable. There are videos on YT. But not everything is understandable to me. Sławomir If you've got Thetis and Voice...
- Wed Jan 31, 2024 2:26 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: DAW - Anan connection via VoiceMeeter Banana
- Replies: 13
- Views: 1480
Re: DAW - Anan connection via VoiceMeeter Banana
Have you got Thetis to work with Voicemeeter? That is the first, necessary step.
- Wed Jan 31, 2024 11:23 am
- Forum: Microphones, Speakers & Audio Hardware
- Topic: DAW - Anan connection via VoiceMeeter Banana
- Replies: 13
- Views: 1480
- Wed Jan 31, 2024 11:19 am
- Forum: Thetis
- Topic: 700DLE/Thetis ext 10 Mhz sorce( AND) correction factor?
- Replies: 12
- Views: 2119
Re: 700DLE/Thetis ext 10 Mhz sorce( AND) correction factor?
The links to the FW with the RF burst fix are located here: viewtopic.php?f=32&t=4972
I believe those will also have the PLL fix.
I believe those will also have the PLL fix.
- Tue Jan 30, 2024 11:25 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: DAW - Anan connection via VoiceMeeter Banana
- Replies: 13
- Views: 1480
Re: DAW - Anan connection via VoiceMeeter Banana
Here is an example of what Mark is talking about. What DAW are you using?
- Mon Jan 29, 2024 5:15 pm
- Forum: Upgrading/Downgrading
- Topic: Is Bootloader working OK for people who are running Windows 11?
- Replies: 23
- Views: 7603
Re: Is Bootloader working OK for people who are running Windows 11?
Follow the link in my 28 Oct post above. It should answer most of your questions about the various options for loading firmware.
- Mon Jan 29, 2024 3:10 pm
- Forum: Upgrading/Downgrading
- Topic: Is Bootloader working OK for people who are running Windows 11?
- Replies: 23
- Views: 7603
Re: Is Bootloader working OK for people who are running Windows 11?
Bootloader does not care about IP addresses. When you boot the ANAN in Bootloader mode it advertises a MAC address only. The Bootloader app sends out a raw Ethernet broadcast packet that the Bootloader firmware in the ANAN responds to. Knowing the MAC address of the ANAN, the Bootloader app then use...
- Mon Jan 29, 2024 1:34 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: So Disappointed But I Rolled it Back. 7000 MK III To Protocol 1
- Replies: 35
- Views: 46962
Re: So Disappointed But I Rolled it Back. 7000 MK III To Protocol 1
I've noticed a frequency offset when using protocol 2 with a 7000DLE MK3. It is around -160Hz. When using protocol 1, the frequency is correct (within several Hz). I asume that with only changing between protocol 1 and 2 firmware, the frequency should be identical. Do you also have the frequency of...
- Fri Jan 26, 2024 6:16 pm
- Forum: Apache-specific Hardware Discussions
- Topic: BCD output from OC interface
- Replies: 15
- Views: 1866
Re: BCD output from OC interface
ANAN pin 9 to AG pin 11 ANAN pin 8 to AG pin 12 ANAN pin 7 to AG pin 13 ANAN pin 6 to AG pin 14 ANAN pin 1 to AG pin 15 On each of the four "band" lines connect a pull-up resistor to +12VDC. This can be done at the ANAN end or the AG end. I appreciate you explaining all of this. Maybe if ...
- Fri Jan 26, 2024 4:54 pm
- Forum: Apache-specific Hardware Discussions
- Topic: BCD output from OC interface
- Replies: 15
- Views: 1866
Re: BCD output from OC interface
ANAN pin 9 to AG pin 11
ANAN pin 8 to AG pin 12
ANAN pin 7 to AG pin 13
ANAN pin 6 to AG pin 14
ANAN pin 1 to AG pin 15
On each of the four "band" lines connect a pull-up resistor to +12VDC. This can be done at the ANAN end or the AG end.
ANAN pin 8 to AG pin 12
ANAN pin 7 to AG pin 13
ANAN pin 6 to AG pin 14
ANAN pin 1 to AG pin 15
On each of the four "band" lines connect a pull-up resistor to +12VDC. This can be done at the ANAN end or the AG end.
- Fri Jan 26, 2024 3:28 pm
- Forum: Apache-specific Hardware Discussions
- Topic: BCD output from OC interface
- Replies: 15
- Views: 1866
Re: BCD output from OC interface
Thanks, that thread is informative... but unfortunately not enough (for me) to get over the hump. :? For starters, I really should state what my goal is. I am attempting to send BCD to my 4o3a 'Antenna Genius' 8x2 switch using a 5C cable. Do I need to 'inject' +12VDC into this circuit? Or do I only...
- Fri Jan 26, 2024 1:19 am
- Forum: Apache-specific Hardware Discussions
- Topic: BCD output from OC interface
- Replies: 15
- Views: 1866
Re: BCD output from OC interface
It's really not that difficult.
There are lots of handy products to add some pull-up resistors to a DE9 connector.
See also this topic: viewtopic.php?f=46&t=4507&p=23384
There are lots of handy products to add some pull-up resistors to a DE9 connector.
See also this topic: viewtopic.php?f=46&t=4507&p=23384
- Mon Jan 22, 2024 11:26 am
- Forum: Thetis
- Topic: 700DLE/Thetis ext 10 Mhz sorce( AND) correction factor?
- Replies: 12
- Views: 2119
Re: 700DLE/Thetis ext 10 Mhz sorce( AND) correction factor?
There is a lengthy, tacked, 5 page thread on GPSDO operation:
https://community.apache-labs.com/viewtopic.php?f=17&t=2499
Read through that and see if all your questions are answered.
If not, then please post your GPSDO related questions at the bottom of that thread.
https://community.apache-labs.com/viewtopic.php?f=17&t=2499
Read through that and see if all your questions are answered.
If not, then please post your GPSDO related questions at the bottom of that thread.
- Sun Jan 21, 2024 11:26 am
- Forum: Apache-specific Hardware Discussions
- Topic: G2 Raspberry Pi5
- Replies: 4
- Views: 814
Re: G2 Raspberry Pi5
It's probably not a good idea to call it a "Pi4". That is a different product. It is a CM4. If and when the Pi Foundation ever gets around to offering a CM5 it is very likely it will be physically compatible and it would be just a board swap. Learn more about the CM4 here: https://www.rasp...
- Sat Jan 20, 2024 6:27 pm
- Forum: Apache-specific Hardware Discussions
- Topic: G2 Raspberry Pi5
- Replies: 4
- Views: 814
Re: G2 Raspberry Pi5
The G2 uses a Raspberry Pi Compute Module 4 (CM4), not a Pi 4. The CM4 did not come out until until 16 months after the Pi 4. Thus it will likely be some time before they produce a "CM5". If you are both adventurous and knowledgeable about this sort of thing there are already many alternat...
- Sat Jan 20, 2024 3:29 pm
- Forum: Thetis
- Topic: Wave Record Never Worked
- Replies: 4
- Views: 953
Re: Wave Record Never Worked
Does this help: viewtopic.php?f=9&t=4944&p=28185 ?
- Tue Jan 16, 2024 11:36 pm
- Forum: Thetis
- Topic: Thetis and Norton security
- Replies: 9
- Views: 1940
- Tue Jan 16, 2024 1:44 am
- Forum: Thetis
- Topic: Direct X dependencies with Thetis
- Replies: 2
- Views: 747
Re: Direct X dependencies with Thetis
What happens is it doesn't work.
A quick search shows that card supports 11.1 (with latest drivers, I assume). But it is an old card...
The GPU is used only for drawing, not for any DSP.
A quick search shows that card supports 11.1 (with latest drivers, I assume). But it is an old card...
The GPU is used only for drawing, not for any DSP.
- Mon Jan 15, 2024 8:45 pm
- Forum: Apache Labs News
- Topic: ANAN-G2 Shipping Update
- Replies: 286
- Views: 3126627
Re: ANAN-G2 Shipping Update
Interesting. I never knew exactly where they were located.
- Mon Jan 15, 2024 11:39 am
- Forum: Digital ("Virtual") Audio
- Topic: cmASIO feature in Thetis
- Replies: 233
- Views: 91421
Re: cmASIO feature in Thetis
And yet it works fine with Voicemeeter. What performance issues?
- Mon Jan 15, 2024 1:39 am
- Forum: Thetis
- Topic: Click tune not working correctly
- Replies: 2
- Views: 785
Re: Click tune not working correctly
Please tell us exactly what version you are running.
- Sun Jan 14, 2024 2:36 pm
- Forum: Digital ("Virtual") Audio
- Topic: cmASIO feature in Thetis
- Replies: 233
- Views: 91421
Re: cmASIO feature in Thetis
Bryan: why can't cmASIO follow the buffer size set by the device driver?
- Sat Jan 13, 2024 9:39 pm
- Forum: Thetis
- Topic: Thetis and Norton security
- Replies: 9
- Views: 1940
Re: Thetis and Norton security
I'm not familiar with Norton, but it would seem it is not fully excluded from all checks. Achieving that level of exclusion would be a goal.
You could also test by disabling Norton temporarily.
You could also test by disabling Norton temporarily.
- Sat Jan 13, 2024 6:56 pm
- Forum: Thetis
- Topic: Thetis and Norton security
- Replies: 9
- Views: 1940
Re: Thetis has crashed
Please edit your title. Thetis has not crashed, it has been blocked by your Norton anti-virus software. Perhaps your virus definitions updated in a way that now has Norton flagging Thetis as a problem. You may need to tell Norton to generate an exclusion for Thetis. Do you run Thetis as administrator?