Hi Scott, Thank you for your answer. There are no cable diagrams at the link you provided. But these are simple things. I'll try some isolation transformer. I will also try to transmit the signal via VAC. I've never done it. I understand that you need to install the "Muzychenko" virtual ca...

I use a DAW and a few plug-ins to process the microphone signal. An RME PciEx audio card is installed in the computer. When I connect the output of the card to the line input of Anan, I can hear quite a lot of hum with the mic turned off. I did not test when I turn on the output from the audio card ...

Hi Scot, Hi Scot, I bought my Anan 7000 DLE MKI in the UK from a well-known large company as a new device. Anan originally had the 2_v2.1.26C.rbf protocol installed. After the first run on Thetis v.2.9.07 Anan didn't work which was very frustrating. I didn't know what the reason was. I wrote on the ...

Hi, you wrote that the correct P2 firmware will work but with errors. For me, the factory P2 software showed errors and the receiver and transmitter did not work. Only errors appeared. That's why I decided to install P1. I can still try to restore P2. Maybe now after connecting the radio directly to...

Hi, today I installed an additional network card. I connected Anan and it works better than connected to the router. You can see a clear difference. I am thinking about reinstalling the firmware again to version 2 since there were errors and the radio did not work. Maybe a direct connection to the L...

i Phil, have you already connected Anan to the Flex PGXL? I have this amplifier and the day before yesterday I got the new Anan 7000 DLE MKII.
Slawomir SP6DLO

Hi, according to the information on the forum my radio should be MKII -Hardware using the EP4CE115F29C8N Cyclone IV series FPGA. Serial number DX8300497A or higher. My serial number is DX8300519A. But the firmware provided for my Anan is Metis_Orion_MkIII_Protocol_2_v2.1.26c.rbf is for MKIII. I have...

Thank you for the information. I have a Dell 4 port PCIEx gigabit network card. I can mount it and instead of the router I will connect Anan directly to this card. I will write how it works.
Regards,
Slawomir

Hi, I am already changing the protocol to v.1 and the radio started working correctly. Sigi DH1KLM helped me a lot. I would like to switch to version 2 of the protocol but I do not know if the radio will stop working again. I think I will reinstall protocol v.2 in a few days. Thank you for your help...

Hello everyone, yesterday I got a new Anan 7000DLE MKII black version. After installing Thetis, the receiver does not work. The messages "sequencer error 256 (Mic)" and ""Sequencer error 264 (DDC Mic)" appear. It was suggested to me on the forum that this is a firmware issue...

Hi All, after 3 years I'm coming back to Anan. In a few days I will have 7000 DLE MKII bought in the UK. Thetis has changed a lot. I like what Rich did. Is version 2.9.0.7 available and where can I download it? Does the new Anan 7000 need to change the protocol to install Thetis 2.9.0.7? 73's Slawom...

Hi to all
or when working remotely when the radio is still powered
when the PowerSDR icon is turned off, the Anan 7000 DLE MKII antenna socket is shorted to ground?
Slawomir

Welcome,
today my PowerSDR has stopped working. Reinstallation did not help. Anan 7000DLE MKII immobilized. I have WIN 10. Please help me solve the problem. I am sending screen. This is probably a WIN10 problem.
Merry Christmas.
S

Hi, I solved the problem. I had to change Driver WDM-KS to MME and everything started to work properly. I don't know why WDM-KS doesn't work. Various configurations are shown on Youtube. Only MME works for me and I will leave it that way.
Greetings to all.
Slawomir

Hi, after VAC configuration I turned on WSJT-X. The Wide Graph shows working stations, the reception level in the Ban Acitivity window is about 70% and there are no working stations. I have enabled CQ and correspondence can see my sign. A few people called me but I didn't see them in the window. I d...

Hi Scott,problem solved. By default, the new version of VAC Capture port and Render port is turned on "auto" I changed to Wave PCi and now everything works ok. In the Window WDM-KS driver in the input and output tab virtual cables are visible. Everything works ok. Thank you for the advice....

Hi Scott, thank you for your answer. I have partially solved the problem. Audio drivers after the WIn 10 update did not work properly. I can already see 4 virtual cables in the HPSDR setup. But only you can see them when the MME driver is enabled. When I turn on the Windows WDM-KS driver, there is n...

Hi,I installed 4 Virtual Audio Cable-Muzychenko. In the Power SDR - audio-VAC setup I choose the MME driver. The input is only Line 3 and line 4 (VAC). The output is VAC 1, VAC 3 and VAC 4 (VAC). This is probably not correct. Which ports should I choose in input and ouput VAC1 audio setup in HPSDR? ...

Hi to all,
I have a problem with my Anan configuration with WSTJ-X program. Please help.
Slawomir

Hi all I have Anan 7000 DLE MKII for several days. I installed the latest version of PowerSDR 3.4.9. It installed for a long time. When I start PowerSDR, the ruler develops a little slowly and jumps occur. The radio works fine. But if I turn on the RX2 then the screen flashes and the rx2 turns on af...

Hi to all,
in my 7000 DLE RX2 not receiving station. By default, RX2 works on ADC2. How do I switch to ADC 1 is all ok. Does the second antenna have to be connected to the second RX on ADC2?
Slavomir

Hi to All,
my Anan 7000 DLE MKII stays with me for 5 days. Yesterday I turned on the first time TX. The output power at 80m is max 64 W. At 28 Mhz only 52W. I don't know what the reason is. Do you have any suggestions on what to do about it? Does the radio need to be sent back to the service?
Slawomir

Hi Sigi, thank you very much for the story. Just yesterday I launched TM-2. Everything works fine. I have already met Anan 7000 DLE MKII. Low output power is my problem. Maximum is 64 W for dummy load on all bands. I don't know if it's a matter of software or regulation inside the radio. Maybe someo...

Hi All I have had Anan 7000 DLE MKII and Elad TM-2 for 3 days. I connected TM-2 to the computer USB port and the green "USB" LED on TM-2 is off. Does Anan have to be connected via USB to a computer? I have a virtual serial port splitter. Is there a configuration program for TM-2? Please he...

Hi Scott,
I understand you perfectly. But probably among many of the Hermes SDR users are those who use factory-built external PA ?
Slawomir

Hi Scott,
Thank you for your answer. Do you know the ready-made factory that will work with my amplifier? I think the switch must be built at the end of the chain and move the full power that the amplifier gives to the antenna. The power output of my PA limits the available solutions.
Slawomir

?Hello all, My Angelia is already working with a hilberling amplifier. But i have problem connecting rx signal to SDR. Herme / Angelia have no tx / rx relay on board. How to make a connection from an external amplifier to the rx socket in the SDR to bring the signal? Do I need to perform an external...

Hello all,
please help how to configure PowerSDR to work with CommCat to log in. I have a physical 4 ports rs232, I added 2 pairs of virtual ports in VPSD
The SDR is not visible in CommCat despite various attempts at port settings in PSDR and CommCat.
Greetings from Wroclaw.
Slawomir SP6DLO

Slawomir, I do not have an HPA-8000B. Indeed, I doubt anyone has a Hilberling amplifier except you! They look amazing. And amazingly expensive! However, a quick look in the HPA-8000B and Apache manuals shows everything needed to understand how to connect to this amplifier... PTT wiring: Angelia J16...

I have SDR Angelia + BPF -out 500mW. How to connect my SDR to Hilbeling HPA-8000B? PA needs a cable connection with CAT. Will without CAT will switch the bandwidth, ptt?
Slawomir