I found if you open the band stack window and unlock the entry you can then dial in a new one and "Update Entry". Be aware what it's doing by default is avoiding the lower 100Hz (which you don't need for most any mode) and also sets a 2700Hz bandpass to give you 2800Hz total width. Mike W9...

Read this:

viewtopic.php?f=32&t=4462

Can you ping the Apache box? That's the first step.
You don't quite explain your network setup.
We need to know addresses, cabling, net mask. Perhaps an annotated diagram?

Of course the modifications are already made. The power supply is designed to handle full power -- 48V at 40A is 1,920 watts and Meanwell power supplies are very efficient at around 90% so plenty of power. The 1000W on the rig is only for CW or Voice -- not FT8 for example which is limited to 500W s...

I got some more information.

The dimensions are 30cm L x 8.5cm W x 4 cm H
Fans are temperature controlled.
It's a non-standard Meanwell supply with modifications to make it RF quiet and quieter fans.

True -- they abandoned the 8000 version due to inability to get parts.
It's now the ANAN-G2-1K they are flogging.

https://apache-labs.com/al-products/1060/110-220v-AC-Power-Supply-for-the-ANAN-8000DLE-MKII.html The rig is limited to 500W for high-duty mode like FT8. But duty cycle has nothing to do with how much power the rig needs. Anytime you push the 1000W you need the amperage to support it regardless of du...

Seems we need a calibration for transmit too then.

As far as I can tell there is no manual adjustment. I'd have to check the code to see where it's saving it.

I did a Level Cal using the XG3 at -33dBm
I now get
0dBm -- with S-ATT at 9 I get 2.2dBm and no ADC overflow
-33dBm -32.1dBm
-73dBm -72.6dBm
-107dBm -106.5dBm

That's getting closer.....

Just to be complete here's my label.

DX8300219

My firmware is 2.1.23 and Thetis 2.9.10

Re-did my test (helps when you plug the sig gen into the right port

0dBm = -2.7dB, ADC1 Overload
-33dBm = -36.7 dBm
-73dBm = -75.1dBm
-107dBm = -111.6 dBm

So not quite linear here...

If I put 0dBm in and S-ATT at 8 I get no overloads....peak shows -2.9dBm

I used an XG3 which I have confirmed the -33dBm and 0dBm levels with an 8920A RMS meter. My 7000DLE MKII with the latest checkout shows this: 0dB = -99.6dBm -33dB = -133dBm So the linearity is correct but the level is wrong. If I recalibrate using the 0dBm level I get the right answers at 0dBm and -...

Can you please quantify those values...."very low" doesn't show that detail.

Have you looked at Ref Pwr on the Thetis meter? What does for Fwd and Ref Pwr show?

FYI...you ARE using Hamlib -- that's what is in WSJTX and JTDX talking over the serial port.

Glad you got it fixed....

I would also recommend Rig Split instead of Fake It.
Fake It is really intended for rigs that cannot do Rig Split.

Mike W9MDB

You don't say what version of WSJT-X you are running...but try this new DLL... ew hamlib for installation directions #1 Shut down WSJTX #2 Download either the 32-bit or 64-bit DLL matching the 32/64-bit version of WSJTX -- hopefully your browser doesn't block it but may warn you multiple times. If y...

And any update on the G2-1K?

They qualified their statement -- "the world's first DPD as a linear amplifier for amateur radio".

Is there an install package for 2.9.0.10 or must we build it?

So I guess you have a tuner now? What model? I have an app I've created (but not released) that works with the LDG and MFJ tuners. It will auto-tune on band change but allow you to "walk the frequencies without tuning (saves on the relays during a frequency walk). It works with FLRig right now ...

I've got GE Force Experience installed but not running.

Then I'd like to see the error message on the latest version I posted -- it has a couple of debug values in it. The error actually comes from the SharpDX DLL which is no longer under development. I forked the repository for it and almost have it compiled. But I can't duplicate the problem. I'm runni...

It's not an artifact -- it's the path to the SharpDX code in the nuget package for SharpDX. Ya'll probably have multiple monitors -- can you also try the resize on the different monitors and see if that makes a difference? This should show the height and width now in the error message which may be t...

Try renaming \users\mdbla\AppData\Roaming\OpenHPSDR
That will allow you to start with a new config.

If that works than something was corrupt.

Mike W9DMB

Here's version that installs correctly now -- I'll note that the Thetis installer in the code seems to want to install the x86 version by default. I had to make a link in the directory to point the x86 directory to x64 so the installer could find the correct 64-bit files. This version has a stack tr...

Try this package -- I added a stacktrace to the error message.

I'm fixing this thing so it will install properly....stand by...

Mike