Hello to all, From one Day to next Day my VAC is defekt. I use it only to hear the Audio with my PC. I get the Message: PortAudio Error: -9999 Unanticipated host error and: PortAudio Error:-9998 Invalid strem pionter System is Win10 Home Version 1803, VB-Cable Driver pack 43, Psdr 3.4.9. I have trie...

Hi Scott,

whats about the Signal-Generator in the PowerSDR?
Is that usable for the Calibration???


73 Erwin

Hi all, If I enable RIT or XIT, the spacebar PTT control will function, however, as soon as a frequency value is entered for either RIT or XIT with the little up/down frequency buttons the spacebar seems to lose focus and no longer controls the PTT function. Clicking on any button or slider in the G...

Hi all,

with my 200D, Rev. 24, 3.4.7, FW 5.0, is the Spacebar working perfekt, also with RIT on.

73 Erwin

May be its a internal Problem with the Graphik UI from Anans/Powersdr ?? I have testet with my 200D V24, the Signal in my Yaesu with Panadapter looks clean.
Also other Station says my Signal clean.


73 Erwin

Hi to all,

here is the link to the German Site, I mean the Version (12 khz) from the US-Site is no longer in Produktion??
I use the 6 khz Version here.

http://www.hoerfabric.de/4/Produkt+LINGUA/
or
http://www.hoerfabric.de/6/LINGUA+Spezifikationen/

It costs here in DL 129 €

73 Erwin

hi to all, the NR2 is very good perhaps the best on our Radios? But, with a strong Signal I have little Artefacts on the Audio. Also with NB2, if the Band are closed it is good, but when I have strong Station, S9+, not on my Freq. but +/- 100 khz, it begins to pumping and distorts with loud Station....

Hi Prem,

sorry for delay, some Problems with my Harley............

I have testet, yes, VFO A is RX1, some thing are difficult, Volume VFO B is only for the Sub-Receiver, i think.


Hope your Touch is running now?

73 from Germany with Snow Erwin

Hi Prem,

sorry, was a Mistake: Vol. VFO B works only for MultiRX.

The correct one is RX2 Volume,
Id-Nr. in the Commands is 222.

That works here perfekt.

73 Erwin

Hi Prem,

the Names are:

Click Tune on off (Id 73)

Volume VFO A (Id 204)
Volume VFO B (Id 205)

Have Fun

Erwin

hi,

with my Anan200D switching from LSB/USB to AM, the Buffer an Filtersize switch to Standard, Filter Type also.
When I switch from AM to LSB/USB its get my personal setup back again. (with Low-Latency-Type)

73 Erwin

Hi Scott and all others,

for my Acom 600S I take 500 and 696 hz.
The 600S Firmware is blocking the "normal" Frequenzys.
Max. 196 - 197 hz differenz between the Tone are working here.

73 Erwin

Scott:

Great.

Erwin

Ok, thank you.

Erwin

Hi Scott,

I don´t know, but the 600s has a frequency-Counter. And I have tested: if the Tones are max. 199 hz different it works. At 200 hz difference it works not.

I think Acom is afraid??

73 Erwin

Hello,

I get an Info from a german Dealer: The 2-Tone Test is blocked from Acom in the Firmware from the 600S.

73 Erwin

Hallo, I have tested 5.2: same as 5.1 Pure Signal is not working (with intern Sampler). It looks like there is no Feedback, PS is on, but no green Lamps, its all Black. Get back to 5.0 all is ok. Another Question: The Button VFO-Lock locks only VFO A not VFO B. Is that a problem with Firmware or is ...

Hello,

I have installed V 5.1, after that Pure-Signal on my 200D, Board 24, is not working. It is on, but no feedback from internal Coupler.
Going back to 5.0 all is ok again.

73 Erwin

Hello Guys, I see also a different in the Display when I use the Tune button, the Peak is now around -40 before 3.4.6 it was around 0 to -10 I think?? The HF-Output is still ok. Also the ATT-Level for Pure Signal is now 0, before 3.4.6 (5) it was around -4 db on 80 m. The Feedback-Level on Pure-Sign...

Hello Scott, all others is working perfekt with the Acom. Yes, use Drive-Power is marked. I tried powerlevels from 5 to 30 Watts, no changes. I am still waiting for an Answer from Acom / Wimo Germany.............. Setup / Tests / Two Tone Test is: Freq. 1 700 Freq. 2 1700 Level 0,000 RF-Power zb. 33...

Hallo all, I have a little Problem: With my new Acom 600 S: I can not use the Two-Tone Signal from PowerSDR openHPSDR 3.4.2. I see the Input on the Display from the 600S and it switched to TX but no output will show, nothing. I use different Spaces between the tones 700/1700 700/1900 and so. Only wh...

Hallo,
its a great work, thanks verry much !!!

But: in Version 3.3.17 i see High SWR-Problem but only on 10 mtrs. Trans. is a Anan 200 D with the new Board.
In V 3.3.9 to 14 perhaps also in .15 was all SWR ok, i think.

73 Erwin

Hello Scott,

Ok, I use Board v24.
I will put a Relay inline the 2nd Antenna to Ground it when TX. Think this is the easy Way(here in DL).

73 Erwin

Hello all,
FW 4.9 works fine on my Anan 200 D, Board Rev. 24.
Thanks to all Programmers!!!


73 Erwin

Hello, I use the Anan 200 D, buy it 8 Weeks ago here in Germany. I do not know my Board-Version. Where can I find it?? I think its a older Modell, with a second Antenna on RX2 I get a Problem with ADC Owerflow. Like the 2nd Antenna is not switch to Ground when I transmit??? Firmware 4.8 do not work ...