Simple 2 CAT command example using SerialSend and COM ports:

SerialSend.exe /hex /devnum 15 /baudrate 9600 "ZZFA00001855000;ZZMD00;"


And NCAT:

echo ZZFA00001855000;ZZMD00 | ncat 127.0.0.1 13013

Great, it has been a slick addition. The old fashion way of using COM ports was quaint, the TCP way is so much better.

Got to ask, why are you using the very powerful 7000DLE and not running the very best software and firmware on it?

Thetis:
viewtopic.php?f=9&t=3817

Protocol 2:
viewtopic.php?f=32&t=3192

It is right here in this forum viewtopic.php?f=6&t=2330

But why would you want to do that??

You probably want Reset On Expiry checked. And then every time you start Thetis you need to enable the Timer (lower right of the GUI, the stop watch, left click it to turn green).

A useful option would be a setting to make the timer start with Thetis, or maybe on the first PTT.

Ruben, will the timer already built in not work?

Stanpix wrote: it is version 2.8.11

2.8.11 then what?

m1tzr wrote:Also the new info bar you say "click the bar to cycle pages" Where is it located, I can't see it for looking?

This is the Info Bar, click anywhere in this area.

I just can't explain the agc rc2 problem... RIchie. Ritchie, I run split sample rates, 192K on RX1 and 1536K on RX2. I stated to note that in my explanation and neglected to note my sample rate on RX2. Although both use the same Bin Width. It is not an issue now that I understand that it changed. I...

Ritchie, can you take a look at Auto AGC in rc2. The offset now seems to be way off, needs way more offset in db, not proportional. On RX1 At 192KHz sample rate my dB Offset now has to be an addition 12dB, or in other terms 12dB of offset puts the Ga line equal to the noise floor line. And and numb...

Ritchie, can you take a look at Auto AGC in rc2. The offset now seems to be way off, needs way more offset in db, not proportional.

Can I add a request for a CAT command to Enable Auto AGC?

You will need NCAT.exe. Download the latest stable command-line zip file from https://nmap.org/download.html This zip file has more than you need. If you want to use my sample StreamDeck Profile you need to match where I install NMAP which is C:\Apps\nmap and once unzipped to there you can delete ev...

Paul, I now have converted all my StreamDeck macros/buttons to use the TCP/IP CAT server (Thanks Ritchie!!!) verse the virtual com ports, in fact I have all the Thetis virtual CATs disabled.

E-mail me an I can share some of the StreamDeck buttons.

You will need SerialSend installed so grab that too https://batchloaf.wordpress.com/serialsend/

Ritchie, I really appreciate all this work you are doing, you taking a superb radio and making it even better! A few of us use VFO Sync and RX2 and we are probably in the minority. At least for a quick fix the RX1 VFO A/RX2 VFO B option you showed would get us by, even though as you said it is not &...

***Update** It seems to be related to VFO B. VFO B will cause the Log4OM Rig switch to show "2" when tuning Thetis VFO B, but it shows it in the left VFO window of Log4OM. Tune Thetis VFO A will cause Log4OM rig to show "1", and again shows the freq in the left Log4OM vfo. Turn o...

OK, thanks Ritchie.

w9mdb wrote:I don't have the TCI Server or the TCP/IP controls.
I'm running Thetis 2.8.11 21k8.

You need 21k9 pre7

Well now that I found that TCP/IP is not TCI and then configured TCI, whenever I try to connect Log4OM via TCI or TunerReminder it causes Thetis to close. And yes I am using 127.0.0.1.

Back to troubleshooting.

Ah yes Ernst, got it now, I got focused TCP/IP and didnt look to find TCI.

Figured I would start a new topic here for this new feature. Having a few questions: 1. Hitting the Default button my port sets back to 13013 but others hams I have talked to say theirs go 50001. 2. I can not get TunerReminder to connect but I can get Log4OM to work, but not using the TCI, it will n...

With the new Auto AGC is there a CAT command to enable it?

Ritchie, the speed up of PS will be a great improvement. Has always been a pet peeve of mine.

Ritchie, the 2 issues I reported ref Mute on start up and the CW switch are fixed. Thanks.

Chris, see a few posts up, Ritchie was able to duplicate this.

It also means you are NOT running Pure Signal

Richie, sorry I found another issue.

Conditions:
RX2 enabled.
RX1 using VAC1 (ASIO)
RX2 using VAC2 (MME)
VAC 2 "Mute will mute VAC" is un-checked.
RX2 MUT enabled

Initial start up there is no VAC 2 output, if I toggle RX2 MUT On then Off then VAC 2 audio appears.