Hi,

Is this redrawing behavior normal with TCI spots?

https://www.youtube.com/watch?v=tc0jNEZN3DM

It is really anoying...

Thanks Ritchie! Agree with "Russian mods", those days I don't answer or call russian stations... EDIT: TCI spots, additional info is just showing "SWL", nothing else... I don't know if it is an issue with Swisslog. Yes, swisslog sends only "swl" as text: SPOT:6W1TG,USB...

Thanks Ritchie!

Agree with "Russian mods", those days I don't answer or call to russian stations...

EDIT: TCI spots, additional info is just showing "SWL", nothing else... I don't know if it is an issue with Swisslog.

Richie, Will be nice to have the option in TCI spots to show the spotter callsign when holding "shift" key like we have on Thetis's spottig system. That info is not included in the the spot message as part of the TCI protocol unfortunately. The additional text is normally for stuff like '...

Hi Richie, I saw it immediately on RX1 , never tested RX2. To correct I had to increase the offset value from 20 to 43 EDIT; an offset value of 20db puts the AGC line on the noise floor I just can't explain the agc rc2 problem... Video : https://youtu.be/T6Ab-cKXGKY (watch it on x2 speed if I am to...

Richie,

Will be nice to have the option in TCI spots to show the spotter callsign when holding "shift" key like we have on Thetis's spottig system.

Richie, thanks for the TCI fix and the new TCI spotting option, works great with Swisslog!

DDS and IF messages existed in TCI an early protocol version when I first looked at it back in 2018/19. It was the only way to assign a vfo frequency. At some point they implemented the VFO command to wrap those two into one somewhat. DDS,IF should be good to go in rc2, over weekend. R. Thanks a lo...

I just tested Swisslog + SunSDR. This is what is sent via TCI on double-click on spot: dds:0,7115000; modulation:0,lsb; DDS: Tuning of the RX's center frequency (center of the panorama) This is what LogHX is sending: modulation:0,LSB; vfo:0,0,7110000; VFO: Set receiver's tuning frequency I guess DD...

Swisslog developer sent me this:



Are these command working with Thetis's TCI implementation?

Hi! Just installed Swisslog 5.103 and made a quick configuration (TCI for Thetis). Mode change is working in both directions. Do you use the dropdown in the topbar to change the mode? swisslog vs thetis.jpg 73 Ernst Hi Ernst and thanks for testing it! Yes, the top bar to change the mode works also ...

I have a TCI issue connecting Thetis with Swisslog logger ( https://www.swisslogforwindows.com/ ). If I change band/mode on Thetis, Swisslog follows my changes, but unfortunately it doesn't work in the opposite way from Swisslog to Thetis. Changes on Swisslog are not followed by Thetis Talked with S...

Many thanks Richie!

Pure signal is engaging very fast right now, congratulations!

Thanks Richie! updated the post with that fix for the phase buffers, was reading something it shouldn't have ;) edit: not sure if it is windows11 or what, but when you extract that zip out over the top of an old version and run it, it does take a while to get going for the first time. Doing a virus...

Thanks Richie!

Richie, thanks for the pre release!

I've noticed that this pre release loads slower (a few seconds) than the previous ones.

Any reason for that?

Thanks a lot Richie!

Just one suggestion for the next release:

Please, can you also dissable auto agc compensation when using the mouse wheel to adjust it?

Have a happy new year!

Could be possible to have an option to disconnect AUTO AGC gain adjust when moving the slider up or down?

w9mdb wrote:I've been using Windows 11 without a problem....but I've been on the prereleases....
This has some info on the error you're getting...
https://recoverit.wondershare.com/firew ... ndows.html

Thanks for the tip, but I've rolled back to W10

After 3 days using W11 without any problem I MUST go back to Windows 10. This morning when I started my PC I got an alert about Windows firewall not working, and I'am unable to start it again, later Windows store stopped working and so many apps didn't work. Thetis connects to my radio, but no signa...

Thanks, Mark. I guess we'll see when Windows 11 finally comes out! I'm waiting for the official release. Scott, Windows 11 is now officially available judging by a Windows update notification I got today! Using Thetis 2.8.11 (10/20/20), P1 at present as I am getting more familiar with this software...

Not just a PowerSDR or Thetis limitation at least with Sound Blaster ASIO drivers...

When running Thetis and ASIO drivers I can't open, for example, a YouTube video at the same time, I always get an error because Windows is unable to play audio.

After closing Thetis YouTube video plays fine.

That's normal, are you using ASIO drivers in "exclusive mode"?

ramdor wrote:Request.

For those that are able, could you check the following file

C:\Users\<user>\AppData\Roaming\OpenHPSDR\Thetis-x64\ErrorLog.txt

for the following :

Index was outside the bounds of the array.

If found, could you email me the txt file.

Thanks, R.

Sent to your email!

The advanced VAC settings are reset to defaults on 21j & 21j2 after restart

Thanks for the reply on Windows 11. As soon as the news of the TPM Ver. 2 requiement were out, all the chips were bought up. My board (MSI) has the socket for the chip, but no chip as of yet. I have seen that there is a workaround for no TPM chip, but don't have the details at hand at the moment. I...

w-u-2-o wrote:

pa1hr wrote:Thanks for this Scott! It helps a lot. No more seq errors and no more audioclicks.

All credit belongs to Jordi, EA3AQR

Thanks Richie!

Have a nice weekend!

New bug detected: When clicking on FM, AM, SAM, DIGL or DIGU, VAC1 is automatically turned off. All other modes working fine. Switching modes implies automatic switching to TX-profile last used in new mode. Is VAC enabled in these profiles? 73 Walter Walter, the problem was related to TX profile......

New bug detected:

When clicking on FM, AM, SAM, DIGL or DIGU, VAC1 is automatically turned off. All other modes working fine.