with a double click on the ATT font you can switch between Step ATT and old ATT, this function is old

Hello, who writes the firmware for Angelia? Do you have the sources of the latest firmware somewhere? I want to try to build in the band filter control of OrionII, so that you have a separate RX filter for both receivers, like on the Orion MK2. Maybe the manufacturer of the firmware could give me so...

Hi there, I had a similar problem with my Orion MKII card, the Micrel ksz9021rl ethernet controller was broken. Excessive heat exposure over a long period of time is suspected. There was a broken TX channel on my board, but it still worked when it was extremely cooling. After the replacement, I inst...

Hello,

have you ever removed the entire database folder?
If not, I would do that first.

It was the same with me

Did you choose the right radio?

have compiled thetis 2.7.0, if you want to test, please ...

https://www.file-upload.net/download-13 ... 0.zip.html

Hi Norbert,

what firmware do you use on the Anan?

Hello, tested version pre8 today, this causes problems for me with the RX2. When I go on the air, you just have a noise level of -30dbm. Some SEQ errors on TX with activated PSA. I don't have all these problems with Pre4. back to pre4. 73´René Update: Tested again today, no problem with RX2. :roll: ...

w-u-2-o wrote:Don't thank me, thank Rick N1GP. He is the firmware guru. I'm just the happy messenger

Hello,

it was primarily aimed at Rick.

so far none seq error´s on pre8 with 2.6.9 b6 software

mny thanks for this work!

hello,

i´have seq 0,1 errors on ddc2 and ddc3 with pre7, back to pre4, without any errors.


best regards

Hi Alex,

read better the Alexbus, the Orion MK2 board outputs 48bit, LPF, BPF1, BPF2, you read the last 16bit, that is the information for antenna / lpf including TX Signal.

regards René

Hi Dave,

if everything is bought new, then Ryzen 2.Gen or wait for the 3.gen.

Hello, tested with Thetis 2.6.2, very common Seq => 1,10,14,40,41 error, with activated 2RX Seq => 56,57,59. When Seq appears, the LAN transmission stops for a short time. If TX, SSB, without audio display 1-2mW TX power on powersdr. Alex SPI Word incorrect, e.g. TX-> 2RX to GND without function, ot...

Hello, with Orion MK2 48bits (6x shift registers) are pushed in series, the normal protocol knows only 32bit. The problems do not concern Anan100 / 10 / Hermes, because they use the same SPI protocol as Mercury. The mistakes were also there and the transmission was slowed down. So this probably only...

Hello, it's an SPI problem, I could control that with a Logicanalyzer. I've programmed a simple sniffer for atxmega for such purposes, which sends the SPI data words per uart. TX and RX load strobes are doing right, but the bits are not set anymore. There is also a bug, if you activate XVTR HF, you ...

Hello Al, first flash the FW again, to 7k dle off, -> bootloader mode switch on, radio on, connect directly to the PC! , - start HPSDR bootloader software version 2.0.4.4 as administrator -> choose the right network -> press "test for bootloader", this may take a while -> rename the Orion_...

Hello,

yes, of course, with activated PureSignal.


regards René

Hello Scott,

With Hermes the 384khz problem does not exist.
Unfortunately, Thetis is still early beta.

Best regards René

Hello, I used an Orion MK2 board for some time. A nice evolution of apache labs. I found two bugs on my board and a 7000DLE at the moment. First: 384000Khz sampling rate with activated PD results in unclean spectrum and audio Second: RF power meter without Alex shows a maximum of 760mW, while at the...