KC2QMA wrote:Got It
https://community.apache-labs.com/download/file.php?id=3984

That's an early version of the instructions.
See the Thetis folder after installing pre-release-4 for a pdf of the most recent version

Yes it does. The lockMode will be enabled.

If you have installed pre-release-4, the instructions for cmASIO are in the Thetis folder.

Hi Jim, Do you have DebugView from sysinternals.microsoft.com? If so, you can use it to see debug output from Thetis while it is starting which will show what went wrong with cmASIO. Otherwise, there's a couple of Voicemeeter pitfalls you can check. Voicemeeter's virtual ASIO driver buffer size shou...

If this is the case, then it would be logical to indicate information about this here in the forum header and specify another backup email! Yes, that would be the logical thing to do. Otherwise, we have absolutely no way to communicate with Apache-Labs. The last time I emailed them, I found myself ...

There's no doubt about that Mark.
It was egregiously hacked!
73

Abhi locked the 'Fraud Alert' thread against replies in the News forum, but if I were able to reply to him, I would say this: I received the aforementioned emails from a fraudster who was posing as Tony. The really bad thing is that the fraudulent email came to me as a reply to email that I had just...

I also noted my UMC status panel shows that it automatically set 64 samples under "buffer mode"; it was set to 8 with VAC so that was nice since I didn't know it needed to be set to 64. I may even break out VMP and give it a whirl again. I have been using my 7300 for digital for quite a w...

Hi Dick, I setup VAC1 and VAC2 just like yours (shown above) in version 2.10.3.5 pre-release-3 using my 7000DLE MKII. Everything works fine. I'm listening to a 40m QSO on 7.157 via RX1/VAC1 and an 80m QSO on 3.915 via RX2/VAC2. Sounds good. Not trying to rub it in. Just trying to encourage you that ...

w-u-2-o wrote:I'm attaching Bryan's cmASIO preliminary instructions here for convenience.

Standby for full instruction guide, which should clear up most questions.
Final draft is being edited and will be released soon.
73!

K1LSB wrote:One question, I haven't been able to find any Thetis mic audio level adjustment that works after I enable cmAUDIO, how are you adjusting your mic input level in Thetis?

Mark,

Use the mic slider on the main console window, just like you did before you started using VAC.

73,
Bryan

Can you confirm that if I want to use the front panel audio again I just need to remove the reg key for now ? Hi Paul, You don't have to remove the whole reg key. You can just delete the text of your asio driver name within the key value, or you can mangle the name somehow (like adding a bogus char...

Revised Timeline: We want to be transparent about the timeline moving forward. We anticipate receiving the updated pallet card within the next 8 weeks, and the upgraded heatsinks are projected to arrive within 6 weeks. With these essential components in place, we are targeting to initiate shipping ...

Roger GT wrote:As a matter of fact. I got my tracking number today!

Great, but how long ago did you order?

KC2QMA wrote:Would be great if you could select a USB audio interface ASIO driver as MIC input under Setup>General>H/W Select.

Hi OM,
Give me a PM here on the forum and I'll send you a link to a WIP that does just that.
Testing phase, if you're brave enough
73, Bryan W4WMT

I tend to force them when running data modes, especially SSTV and the like. There is nothing wrong with them afaik, but their state is not stored along the with the TX profile atm. Okay, cool. I didn't realize they weren't being stored in the TX profile. I've been working on Issue #87 with Sherman ...

ramdor wrote:VAC Audio Force In (rx1 + rx2)
VAC Audio Force Out (rx1 + rx2)

Hi Richie,
Something wrong with the resampler ratio "Force" functionality?
73,
Bryan W4WMT

Not a tick of a box.
Do that with the "Pan" sliders, i.e. slide one all the way to the left and the other to the right.
73!

ct1iqi wrote:G2 100W no display:
ordered July 3 2023,
delivered Sept. 1 2023

It's been almost one month since the last shipping update report!
Does that mean the shipments have coasted to a halt?
Or does it mean the shipments are now occurring so timely that the issue is moot?
73,
Bryan

Tony, is your G2 running Protocol-2?
73, Bryan W4WMT

Hi Tony,

What sort of audio interface are you using now on your G2?

73,
Bryan W4WMT

Take what?

Is there a protocol-2 image for the TRX DUO / Red Pitaya yet?
Bryan

Hi All,
How do we know the rumbling sound wasn't actually a signal on the band?
His panadapter is zoomed out so far, I can't squint hard enough to see if the rumble is actually within the receiver passband or not.
73,
Bryan W4WMT

Not aware of the ".26" series.
But you did try the ".27A/B/C/E/F/G" series, right? Those are the ones that work FB here on my EP4CE based Orion.
73, Bryan W4WMT

Sorry to reincarnate this thread after all this time. With the possible exception of Juha above, no one has reported successfully running TCI with the RF-KIT amplifiers. If there are successful users out there anywhere, will you please kindly post a screenshot of your Thetis setup tab to help me get...

W7GES wrote:i monitored via my TS-890 on the other side of the shack and the audio sounded fine.

Hi George,
When using the TS-890 as an off-air monitor while transmitting on your G2, how did the audio latency seem to you?
73,
Bryan W4WMT

Hi Laurence,
I remember, from your SDRA 2022 presentation, that you were favoring 4096-byte DMA transfers on the PCIe bus for the various streaming channels within Saturn. Did you finally settle on that number, or were there further refinements?
73,
Bryan W4WMT

Yes, there was a "D" build, but it was DOA (according to Rick).
73!

EDIT:
I meant to say, there was a Orion_MkIII_Protocol_2_v2.1.27D.rbf, is that the one you're looking for?

Looks like the 7000DLE was taken down from the Apache Labs website over the past weekend.
Too bad, it was a good rig
73,
Bryan W4WMT