pemmel wrote:Scott
I applied all of your suggested fixes and it now WORKS.

You got it!

This post is old and predates that change to the UI design. I'll update it tomorrow.

You can certainly use a USB microphone, but you will have to give up ASIO and it's latency advantages because, AFAIK, there are no ASIO-capable USB mic's. That said, there are a lot of outstanding USB mic's from the likes of Rode and others. However, you are correct in your assertion that the fancy ...

VAC parameters are saved as part of your transmit profile. Set them, save your TX profile, then you'll be all set.

I forgot to ask you for a screen shot of the setup screen for WSJT-X. Please post that as well so that we can check proper assignment of Cables 1 and 2 vs TX and RX. Do not use DirectSound. Use MME. Change your sample rate to 48KHz. Enable the Stereo checkbox. Change your RX and TX gain to 0dB. It i...

This is a well known problem with both PowerSDR and Thetis VAC operation. Periodically, and for reasons unknown, the VAC audio channel will become unstable. This is normally, but not always, indicated by a rapid accumulation of under and/or overflow counts. This condition exhibits itself as distorte...

Please post screen shots of your Muzy VAC control panel and the Thetis VAC1 setup screen.

I'm assuming you remembered to enable VAC1 on the main Thetis console.

Let's go easy folks (myself included!), I don't want to have to lock this topic ;) There's stuff the Flex does that I wish Apache/Thetis does, and vice versa. Same for ExpertSDR/SunSDR. We all have to choose what works best for us. Those who are lucky enough to own two out of the three (not sure any...

No, read what he wrote. Muzy VAC is working fine for PowerSDR. Therefore it is a Thetis config. error.

Either way it's a subject for another topic.

VAC does not work with Thetis. When I power ON PowerSDR VAC works as it should but no joy with Thetis powered on, no audio into WSJT-X. I checked all of the audio settings in both apps and that was no joy. I am running VAC from Eugene Muzychenko (I miss spelled his name so many times) I originally ...

I2NOY wrote: Can you briefly suggest the configuration of VoiceMeeter Banana to connect Thetis audio to WSJTx?

See here: viewtopic.php?f=13&t=4343

This should work for most any common ham software that needs to move audio to/from Thetis/PowerSDR. These are the most basic settings. There are layers and layers beneath this for various tweaks. But this should at least get you to square one: audio moving reliably between Thetis/PowerSDR and such a...

I am a little puzzled by what I am seeing on the 40 meter band vs. other bands (same multi-band antenna used on those bands). There is nothing to be puzzled about. The linearity of the RF chain from the DAC output to the coupler in the amp can be different on every band. The curves you are seeing a...

I honestly don't know what will happen if you try to import a PowerSDR database into Thetis. It's been years since I ran PowerSDR. Worse comes to worst, you just reset the database and put the calibration factors in manually.

What Sigi said. It's open source. All are welcome. The more the merrier! Obviously it's better for us non-developers, and arguably developers, too, if development is done in an organized fashion on Github. That's the whole point of a tool like Git. It brings automation and configuration management t...

Thanks a ton for that, Ron!

I found that ALT-B is basically broken, and I found that CTRL+R is AGC gain increase.

I'm such a dummy. I did not point out to you explicitly that you MUST use the latest version of Thetis, the successor to PowerSDR, to run Protocol 2. I bet you tried with PowerSDR? Get the latest version of Thetis here: https://github.com/ramdor/Thetis-2.9.0/releases/download/v2.9.0.6/Thetis-v2.9.0....

The MKIII stuff will not run on your older unit. Shouldn't have even tried it.

Did you confirm that your NIC is GigE? Did you at least get a link light and a GigE indication on the NIC?

:) And now that you are more comfortable with Bootloader, it is past time for you to load Protocol 2 firmware. Just be sure you have a GigE NIC and that your Ethernet cable is 100% good to go (all four pairs intact). If you have an older 7000 look here: https://community.apache-labs.com/viewtopic.ph...

Thanks Sigi and Joe. I will try to give it a whirl this week!

The metis renaming nonsense is covered in the instructions I referenced. It is annoying! Try doing a Windows repair operation: https://www.windowscentral.com/how-use-dism-command-line-utility-repair-windows-10-image Use SFC first, then DISM. Super basic questions: do you get a link light on the ANAN...

If Bootloader finds it but you can't ping it, then either a) You are forgetting to move the Bootloader switch back to the normal position (seems doubtful given the technical nature of your post) b) The IPV4 settings on your NIC are wrong (again, unlikely) c) The firmware needs to be reloaded and the...

After some tries, yesterday I was able to use ASIO drivers on both Thetis and WSJTx and it is working pretty good. ;) Unfortunately, that's not what you did. You are still not using ASIO with WSJT-X. The solution is to install ASIO bridge, also called Hi Fidelity Virtual Cable. This merely adds an ...

By definition turning on PureSignal will result in more accurate reproduction of audio. Period. Dot. Less IMD is less IMD. You are suffering from a psychoacoustic phenomenon whereby you merely prefer what you hear with PureSignal turned off. This is quite common, particularly in audiophiles. Technic...

Will you be working on an installer for this, Joe?

On the Apache, the sampler cable then plugs into the rear RX BayPass connector right... I am with the account that it is there where it connects, but a colleague tells me that it is in EXT1 I already have doubts... Somewhere during the production of the ANAN-200D this changed. Older 100D and 200D m...

Not Tony, but... I think what Tony is saying is that he is using the ASIO driver mode of the Thetis VAC interface to connect to Voicemeeter, and that is all. Because there are no other amateur radio app's at this time that support ASIO. All of them, e.g. WSJT-X, Fldigi, etc., attach to Voicemeeter u...

Hello everyone, I have a Murcury 3s amplifier, a 7000DLE blackface MKII latest version of FPGA, I wanted to use PS and I have a -55 dbm coupler reading this post everything makes me think that the Coupler will not be valid, the use of the amplifier is normally around 700 w peak. Thank you It will w...

You are worried about nothing. You can leave Bypass on TX enabled regardless of the state of PureSignal. It doesn't matter if the amp feedback comes in when you aren't using it. Just leave it alone unless you want to use PureSignal without the amp.

I went on 20 meters and talked to a fellow told me I was +40dB/S-9 and had a Panadapter for visualizing my signal and when I switched the PS on and OFF he was blown away by how clean the TX looked. And that's the beauty of linearization. And that's why Apache/Thetis radios have the best sounding au...