Search found 70 matches

by cLicari
Mon Nov 11, 2019 2:33 pm
Forum: Thetis
Topic: 2.6.9
Replies: 271
Views: 14767

Re: 2.6.9

Been running radio in receive for hours with no problem. Then was in QSO and had some error message flash across bottom of display and then locked up. Here is the seq log....

seq log-1.txt
(32.59 KiB) Downloaded 13 times

Carl
NX5T
by cLicari
Sun Nov 10, 2019 10:59 pm
Forum: Thetis
Topic: 2.6.9
Replies: 271
Views: 14767

Re: 2.6.9

My report: pre4 is the best of the bunch on my 8000. In more detail: Pre2 worked but PS was unstable. Pre1 worked fine. But pre4 is definitely demonstrating superior PureSignal performance and just "feels" smoother overall. No seq errors at all with pre1 or pre4 unless I make the PC sweat...
by cLicari
Sun Nov 10, 2019 7:34 pm
Forum: Protocol 2 (all radios)
Topic: New 7000/8000 Orion MKII Protocol 2 Firmware Topic
Replies: 25
Views: 1989

Re: New 7000/8000 Orion MKII Protocol 2 Firmware Topic

Carl: does it work better or worse than pre1 or pre2? Which is best for you? And are you using a 7000 or 8000? Scott.. Running an 8000DLE. I can't say one is any better than another. Once it reaches the point of failing all of them fail again repeatedly after a short amount of time (seconds). Did t...
by cLicari
Sun Nov 10, 2019 4:00 pm
Forum: Protocol 2 (all radios)
Topic: New 7000/8000 Orion MKII Protocol 2 Firmware Topic
Replies: 25
Views: 1989

Re: New 7000/8000 Orion MKII Protocol 2 Firmware Topic

My report: pre4 is the best of the bunch on my 8000. In more detail: Pre2 worked but PS was unstable. Pre1 worked fine. But pre4 is definitely demonstrating superior PureSignal performance and just "feels" smoother overall. No seq errors at all with pre1 or pre4 unless I make the PC sweat...
by cLicari
Sat Nov 02, 2019 5:36 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

I agree, I have seen this alot in the past based on serial number. Try this one as I have seen this version be more stable with some 7000DLE's, Orion_MkII_Protocol_2_v2.0_pre1.rbf . If you need the firmware, send me an email and I'll send it to you. I did try both pre1 and pre2 a few weeks ago. Unl...
by cLicari
Sat Nov 02, 2019 4:28 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

I agree, I have seen this alot in the past based on serial number. Try this one as I have seen this version be more stable with some 7000DLE's, Orion_MkII_Protocol_2_v2.0_pre1.rbf . If you need the firmware, send me an email and I'll send it to you. I did try both pre1 and pre2 a few weeks ago. Unl...
by cLicari
Sat Nov 02, 2019 4:09 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

As much as I hate to, I must abandon P2 and 2.6.8. After running all iterations of the software and firmware, intermittent lockups persist with variations from complete freeze ups to what appears as half of the display going into a slow motion panafall with a distorted audio present. There is no tel...
by cLicari
Wed Oct 23, 2019 6:48 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Richie... After deselecting Network Watchdog Thetis ran perfectly, for extended periods, some unattended to test it, for three days! After trying the RF Delays noted above I shut down for the evening, but forgot to return the RF Delay setting value back to 30. Later that night I turned the radio ba...
by cLicari
Wed Oct 23, 2019 5:28 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Richie... Even with RF Delay set to 0 I still see the spike. The only way I have found to not see the spike, and this isn't a solution, is to deselect the "MIC" button before unkeying. Thx Carl try adding a bunch of RX delay, say 300ms, see if it vanishes. If you are seeing it after relea...
by cLicari
Mon Oct 21, 2019 10:23 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Richie... Even with RF Delay set to 0 I still see the spike. The only way I have found to not see the spike, and this isn't a solution, is to deselect the "MIC" button before unkeying. Thx Carl try adding a bunch of RX delay, say 300ms, see if it vanishes. If you are seeing it after relea...
by cLicari
Mon Oct 21, 2019 8:45 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Richie... When unkeying mic I see what appears to be a momentary energy spike that peaks on the selected frequency and is the width of the panafall. Is there any correlation to this and what you just described? Is there a way to eliminate it? Very disconcerting to see. This is nothing new though. F...
by cLicari
Mon Oct 21, 2019 4:51 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Running the latest updates. Not sure if it is an issue? when keying TX (MOX or PTT) I get a very quick sort of spectrum flash / jump / peak? hard to explain. Might be just a setting. I'll try and video record what its doing. This is because drawing thread is now not blocked, and the data arrays for...
by cLicari
Sun Oct 20, 2019 4:24 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

If you have network watchdog turned on (settings,general,hw) then the plug will be pulled (click power off on thetis) if there are no events on the listening network socket (ie no data) for 3 seconds. It is also possible that the function WSAWaitForMultipleEvents is failing outright, which would re...
by cLicari
Sun Oct 20, 2019 3:19 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Turned the radio off at dinner time. Later that night turned radio back on and after about an hour had four disconnects, two of which were within seconds of each other. It's like I hit the "Power" button. It locks up, the power button light turns off and the radio relay clicks, like a nor...
by cLicari
Sun Oct 20, 2019 1:33 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Re: the network. The Anan is on it's own subnet and direct to the computer. However, the Ethernet card IS a Realtek TP-Link Gigabit PCI Express card. But it works without issue with P1 and OpenHPSDR 3.6.9. Would you still recommend switching to an Intel card? honestly, I dont know, it is just inter...
by cLicari
Mon Oct 14, 2019 4:58 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

ADVICE for all people having Seq errors: After reading in Latency monitor help page, that "hard pagefaults are the most common cause of audio dropouts" I've followed one of the suggested solutions: Disable the pagefile (windows Virtual Memory) altogether. You can disable the pagefile by r...
by cLicari
Sun Oct 13, 2019 2:22 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Well today I have tried Thetis c5 with P2 v1.7, v1.8, v1.9 (which has been working fine until today), v2.0 pre-beta. None of them are working well enough to use for any length of time, let alone reliably. I'm beginning to think it may be the current Thetis c5 and not the firmware. Don't know what c...
by cLicari
Sun Oct 13, 2019 2:43 am
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Well today I have tried Thetis c5 with P2 v1.7, v1.8, v1.9 (which has been working fine until today), v2.0 pre-beta. None of them are working well enough to use for any length of time, let alone reliably. I'm beginning to think it may be the current Thetis c5 and not the firmware. Don't know what c...
by cLicari
Sat Oct 12, 2019 9:06 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Well today I have tried Thetis c5 with P2 v1.7, v1.8, v1.9 (which has been working fine until today), v2.0 pre-beta. None of them are working well enough to use for any length of time, let alone reliably. I'm beginning to think it may be the current Thetis c5 and not the firmware. Don't know what co...
by cLicari
Sat Oct 12, 2019 5:11 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Thanks Gary.
I'll give it a try before going back to P1, which I hate to need to do.

Carl
by cLicari
Sat Oct 12, 2019 5:06 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Gary... No, does it run on the 8000DLE?
I don't see it listed in GitHub
by cLicari
Sat Oct 12, 2019 4:50 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Been running c5 with P2 v1.9 but starting to have intermittent problems with Thetis locking up. Sometimes I'll see a few "seq" errors and then it will lock up. Other times no "seq" errors but an audio cutout then it locks up. I switched to P2 v1.7 with no improvement, more lockup...
by cLicari
Tue Oct 08, 2019 6:02 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Have noticed in ver c4 and c5 when Thetis is shut down on a band other than 20m, the next time Thetis is launched and I select 20m band the drive level has changed to 100, not the lower level as previously set. Anyone else seeing this?

Carl
NX5T
by cLicari
Sat Oct 05, 2019 12:12 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Richie.... Loaded c4 last night and have noticed "Step Tune" of 500Hz is only moving tuner 50Hz per mouse wheel click now. Carl NX5T odd, 500 will become 50 if shift is held at time of wheel change. Perhaps the shift state is locked on somehow will check. Tried it again several times with...
by cLicari
Sat Oct 05, 2019 11:30 am
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Richie....

Loaded c4 last night and have noticed "Step Tune" of 500Hz is only moving tuner 50Hz per mouse wheel click now.
Also no audio regardless of AF level in RX2.
Thx,

Carl
NX5T
by cLicari
Sat Sep 28, 2019 3:04 pm
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Running c1 full screen on 40" 4k monitor 60fps smoothly...
I did lose the blue panafall background though. Disable picDisplay is not selected.
Is c2 available for download?

[img]
2.6.8%20c1.JPG
[/img]

Great job Richie!
by cLicari
Wed Sep 25, 2019 2:46 am
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Wow! That's a game changer for anyone with a high end system and video card!
Can't wait!
Thx Richie

Carl
NX5T
by cLicari
Mon Sep 23, 2019 3:59 am
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

I have just noticed a bug when running any version of Thetis with either Commander in DXLab or DDUTils. If I try and turn on the CWX tab while running those utilities, Thetis will freeze and crash. If I only load Thetis and not my logging program or DDUTils, CWX works normally. I have had several o...
by cLicari
Fri Sep 20, 2019 4:20 am
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

No worries, and I agree, this is not significant.
Thanks for all your efforts.
Much appreciated.
Carl
by cLicari
Fri Sep 20, 2019 3:51 am
Forum: Thetis
Topic: 2.6.8
Replies: 565
Views: 32780

Re: 2.6.8

Fresh install yesterday showing same gaps others posted....
Carl

Go to advanced search