Search found 26 matches
- Mon Jan 22, 2024 11:49 pm
- Forum: Thetis
- Topic: Thetis v2.10.3.5 final release
- Replies: 97
- Views: 170683
Re: Remove, or Change, Tx Slider Limit To Adjustable Value
Running x64 Thetis v2.10.3.5 u2 on Win10 connected to ANAN-100B. Works pretty good. However, when I went to use the direct Watts tx slider recently, I noticed there is now a limit, and "over 69%" indicator placed on the main panel slider for 6m, i.e. a 70% -100% of FS red line and no value...
- Fri Nov 17, 2023 6:40 pm
- Forum: Thetis
- Topic: RX2 issue 2.10.3.4 pre release 5
- Replies: 9
- Views: 4879
Re: Thetis 2.10.3.4 pre release 5 - CPU Meter
V2.10.3.4 pr5 Win10 x64 protocol 2 installed and working fine on my ANAN 100B, except that there is no status bar CPU meter. Though not updating (stuck on 100%), it was there on my previous running release and did update on even earlier releases. The CPU meter's update rate is in settings>display>re...
- Thu Nov 09, 2023 12:06 am
- Forum: Thetis
- Topic: Thetis v2.10.3.3 released
- Replies: 103
- Views: 62043
Re: Thetis v2.10.3.3 released
Been using v2.10.3.3 for a couple days now and have not noticed any problems running my ANAN-100B, except that the bottom of screen CPU Usage meter does not update and reads 100% at all times in either Thetis or System. I think the Usage meter actually stopped updating when I updated to v2.10.0. The...
- Sun Aug 06, 2023 4:24 pm
- Forum: Thetis
- Topic: Version 2.10x64 Tx Filter Outline Bug
- Replies: 0
- Views: 8145
Version 2.10x64 Tx Filter Outline Bug
Installed Thetis v2.10x64 6/19/23 on my ANAN-100B and running for a couple weeks. One small problem/bug so far - tx filter outline on panadapter screen shows a positive offset, i.e. it is at a higher frequency (the tx shows almost completely outside and below the filter outline) than the tx, which i...
- Sun Apr 17, 2022 5:38 pm
- Forum: Thetis
- Topic: Thetis v2.9.0 - Updates and Issues
- Replies: 431
- Views: 112329
Re: Thetis v2.9.0 - Updates and Issues
V2.9.4 installed on Win10 and working with my ANAN 100B. Default PA settings for the 100B are reasonable, but not as fine tuned as my previous ones (Thanks for reminder to save them). Seems to be working fine so far.
- Fri Apr 15, 2022 3:57 pm
- Forum: Thetis
- Topic: Thetis v2.9.0 - Updates and Issues
- Replies: 431
- Views: 112329
Re: Thetis v2.9.3 Upgraded from 2.8.11 21k7 on ANAN 100B
Just wanted to let users know, I have upgraded my 2.8.11 install to 2.9.3 and it seems to be working fine. It is early, of course (only a few hours on it now), but I like it and have seen no problems. I just exported my old database for comfort. Opened the new download installer and it converted the...
- Sun Jan 03, 2021 1:42 am
- Forum: Thetis
- Topic: Thetis 2.8.11 Rx Level Calibration
- Replies: 4
- Views: 2966
Re: Thetis 2.8.11 Rx Level Calibration
I think I get the operation now. Thanks for your help.
BTW, the lower right hand amplitude readout seems to show the right value if the largest signal in the band is right on the center (VFO) frequency, and it is within the set rx filter by itself. Otherwise, the value is pretty far off.
BTW, the lower right hand amplitude readout seems to show the right value if the largest signal in the band is right on the center (VFO) frequency, and it is within the set rx filter by itself. Otherwise, the value is pretty far off.
- Sat Dec 19, 2020 1:11 am
- Forum: Thetis
- Topic: Thetis 2.8.11 Rx Level Calibration
- Replies: 4
- Views: 2966
Re: Thetis 2.8.11 Rx Level Calibration
It makes sense that the pan adaptor level readings should be affected by the the bin width being used in the FFT and matches what I see when rechecking while adjusting the bin width. I have not had much experience with spectrum analysis so did not catch the bin width to signal width measurement rela...
- Tue Dec 15, 2020 10:24 pm
- Forum: Thetis
- Topic: Thetis 2.8.11 Rx Level Calibration
- Replies: 4
- Views: 2966
Thetis 2.8.11 Rx Level Calibration
Been running Thetis on my ANAN 100B for quite a while now. Finally, decided to try calibrating my (panadapter and digital readout display). Found some interesting things that I would like to see comments on. I am running 2.8.11 on latest Win10 (64 bit). My calibration input signal is from a 10MHz GP...
Re: 2.7.0 Feature Request - Tune Timeout
I just found I had left my radio on tune for a good 30min - lucky I have tune set for pretty low power. Hope I never do that again, but I am thinking a Tune timeout would be nice.
- Thu Jun 04, 2020 11:11 pm
- Forum: Digital ("Virtual") Audio
- Topic: VAC Problem
- Replies: 8
- Views: 9656
Re: VAC Problem
VAC 4.62 would not work for me after my PC updated to the Win10-64 2004 release. Going back to 4.60 works with 2004. VAC 4.62 did work before the 2004 update and also works with Windows Media Player, VLC, WSJTx and FLdigi on 2004. Problem would seem to be with OpenHPSDR. FWIW, a single VAC channel w...
- Wed Jun 03, 2020 4:24 pm
- Forum: Digital ("Virtual") Audio
- Topic: VAC update (muzychenko)
- Replies: 2
- Views: 5015
Re: VAC 4.62
On my system (ANAN-100B, Win10 2004) VAC version 4.62 does not work with Thetis (v2.6.9 and v2.7.0a3) or OpenHPSDRmrx 2.4.9.0. VAC 4.62 did work before the 2004 update. VAC 4.60 does work with 2004. FLdigi, WSJTx, VLC and Windows Media Player work with 4.62 on 2004. Voicemeter va works with OpenHPSD...
- Sun May 31, 2020 1:45 am
- Forum: Thetis
- Topic: Thetis v2.6.9 Install Problem
- Replies: 14
- Views: 8709
Re: Thetis v2.6.9 Install Problem
Sorry, missed the vac section. Tried Voicemeter and it appears to work - just one tx test so far. Funny though that both FLdigi and WSJTx can still use Virtual Audio Cable channels (I can send and receive between the two programs) but Thetis does not. I have been using VAC with it HPSDRmr/Thetis for...
- Sat May 30, 2020 11:41 pm
- Forum: Thetis
- Topic: Thetis v2.6.9 Install Problem
- Replies: 14
- Views: 8709
Re: Thetis v2.6.9 Problem with Win10 2004
My PC did the 2004 update and vac connections to/from Thetis (v2.6.9 and v2.7.0a3) broke. Appears that latest FLdigi and WSJTx can connect to my vac's, but Thetis will not. It also does not show in the Win10 "app volume and device preferences" window as it used to. Thetis will connect to t...
Re: 2.7.0
a3 build running fine so far (kind of early yet) on my ANAN 100B. Did not find it in the change log. but I can use my Rx only antenna on port 1 (marked Rx only in setup) while Tx'ing on port 2 or 3. This annoying (possibly dangerous) bug was in the last few versions, including 2.6.9. If you had a Tx...
- Tue Feb 04, 2020 4:49 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: Hermes Protocol 2 Gigabit firmware for ANAN-10E & 100B
- Replies: 3
- Views: 6847
Re: Hermes Protocol 2 Gigabit firmware for ANAN-10E & 100B
Been using P2 fw 10.3 on my ANAN-100B for at least a year now and can not remember having any crashes. I do mostly digital (WSJT usually) and have only two problems: 1) On 6m, the preamp fails to be switched in after tx, about every four tx>rx cycle. The preamp will switch back on after one or a few...
- Thu Dec 26, 2019 4:06 pm
- Forum: Thetis
- Topic: ANF Setting Not Saved
- Replies: 0
- Views: 4122
ANF Setting Not Saved
For the last few versions (don't remember when I first noticed it) and in my current version (v2.6.9b6), the ANF function is not saved between launches. The ANF function also does not seem to be accessible from any of the v2.6.9 "collapsed" view controls - ANF is pretty handy for digital m...
- Tue Sep 17, 2019 4:05 pm
- Forum: Apache Labs News
- Topic: Introducing the ANAN-8000DLE MKII
- Replies: 101
- Views: 117667
Re: Introducing the ANAN-8000DLE MKII
I also would like some update/status on the 8000DLE. I am ready to upgrade (from a 100B) to more power and performance.
- Thu May 16, 2019 3:38 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: 14-bit Hermes (10E and 100B) Protocol 2 Firmware Topic
- Replies: 17
- Views: 25496
Re: P2 version 10.3 released for 14-bit Hermes (10E and 100B)
Been using the new V3 FW with Thetis 2.6.7 on my 100B. Everthing seems to work, except the 6m preamp is not always turned back on after tx (happens about 25% of tx's). Clicking the Thetis tune button on/off a time or two returns the preamp, cycling the disable preamp on rx button in filter settings ...
- Sat May 04, 2019 11:02 pm
- Forum: Thetis
- Topic: Thetis 2.6.7 released
- Replies: 5
- Views: 6370
Re: Thetis 2.6.7 released
Just installed Thetis 2.6.7 with the ANAN 14bit 10.3 FW (on my ANAN-100B) and it appears to be working fine, at least some FT8 QSO's achieved. Unlike Thetis v2.6.6, it does not run with the 10.2 FW and puts up a message saying 10.3 is needed. The boot loader installed 10.3 with no problem. For some ...
- Sun Apr 21, 2019 1:10 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: Anan 10 and protocol 2 - No Rx ?
- Replies: 8
- Views: 13714
Re: Anan 10 and protocol 2 - No Rx ?
FWIIW, I am now running Thetis 2.6.4 on Win10 to operate an ANAN-100B running the 14bit P2 v10.2 FW. It seems to work fine on HF through 6m, at least on FT8 and SSB phone. I have had 2 program crashes of maybe 100 transmissions on 6m though, so maybe not perfect. Hermes P2 v10.7 loads without any bo...
- Tue Nov 20, 2018 9:54 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: GPSDO Tutorial?
- Replies: 129
- Views: 189368
Re: GPSDO Tutorial?
I did messed up on the output. It is ~1.5Vrms unloaded and ~1.2Vrms/15dbmW into 50 Ohms.
- Tue Nov 20, 2018 9:17 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: Frequency Resolution/Accuracy for OpenHPSDR + 100B
- Replies: 5
- Views: 5336
Re: Frequency Resolution/Accuracy for OpenHPSDR + 100B
Do you know if any of the other ANAN compatible programs (piHPSDR, SDR console, Thetis), or even the Hermes FW can provide/output accurate subHz resolution?
- Tue Nov 20, 2018 3:48 am
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: Frequency Resolution/Accuracy for OpenHPSDR + 100B
- Replies: 5
- Views: 5336
Re: Frequency Resolution/Accuracy for OpenHPSDR + 100B
Good to know. Do you know if OpenHPSDR repeats better than 1Hz resolution to CAT connections - say allowing the WSJT-X cal function to record correctly for fractional Hz drifts?
- Mon Nov 19, 2018 11:14 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: Frequency Resolution/Accuracy for OpenHPSDR + 100B
- Replies: 5
- Views: 5336
Frequency Resolution/Accuracy for OpenHPSDR + 100B
Does anyone know what the max resolution and actual accuracy of the 100B's VFO frequencies used within the 100B's FW, OpenHPSDR and reported via CAT are?
I am wondering whether a GPSDO external reference is worthwhile if it's not much better than the cal function and VFO readouts.
I am wondering whether a GPSDO external reference is worthwhile if it's not much better than the cal function and VFO readouts.
- Mon Nov 19, 2018 3:34 am
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: GPSDO Tutorial?
- Replies: 129
- Views: 189368
Re: GPSDO Tutorial?
I just got one of these and it has a CTS 970-2178-46 oscillator in it with uBlox GPS. It seems to be an older CTS model 115 OCXO. 10MHz output is ~10Vrms unloaded. I have an ANAN-100B (Hermes) so am going to add an auto-select/buffer board (w7ay/Kok Chen Hermes Reference Oscillator with no OCXO load...