Search found 14 matches

by Mike_N1JEZ
Tue Oct 13, 2020 1:38 pm
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 219
Views: 21124

Re: Thetis 2.8.8 Released!

Doug,

I missed the * Doh!

Tnx, Mike
by Mike_N1JEZ
Tue Oct 13, 2020 12:19 pm
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 219
Views: 21124

Re: Thetis 2.8.8 Released!

I installed the 64 bit 2.8.8 version of Thetis on a core 2 duo laptop. Processor is T6670 @ 2.2 GHz. Win10 Pro 64bit vers 2004. 8GB ram installed. When trying to launch, it fails at port audio initialization. 32 bit version is fine. I did a "coreinfo" dump and it says AVX is supported. C:\...
by Mike_N1JEZ
Mon Oct 12, 2020 4:56 pm
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 219
Views: 21124

Re: Thetis 2.8.8 Released!

Tried both and they work on all of my machines except one. It's the 64 bit version that is the issue. Same as the other reports. No problem with 32 bit.

Mike, N1JEZ
by Mike_N1JEZ
Tue Apr 16, 2019 11:19 am
Forum: Protocol 2 Firmware (all radios)
Topic: P2 Firmware Bugfix Release for All Radios (except 14-bit Hermes)
Replies: 2
Views: 2858

Re: P2 Firmware Bugfix Release for All Radios (except 14-bit Hermes)

Hi Scott,

Any idea whether there will be a "B" version of Protocol 2 for Hermes-ANAN-100 to address the output filter issue?

Mike
by Mike_N1JEZ
Tue Mar 12, 2019 10:29 pm
Forum: Transverters
Topic: Microwave transverter issue
Replies: 4
Views: 6989

Re: Microwave transverter issue

Has there been any news on this issue? Trying to set up transverters with an offset greater than 2000 is a problem.

Tnx,
Mike
by Mike_N1JEZ
Sun Nov 18, 2018 1:44 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: ANAN-100 low 10/12m output with LPF enabled.
Replies: 16
Views: 6878

Re: ANAN-100 low 10/12m output with LPF enabled.

Which version of the firmware are you using? There was an issue with the early ANAN-100 units where the wrong filter was selected. There was a firmware version (on the Apache site as I recall) that addressed that issue. I use it on my ANAN-100. I'd have to dig for more specifics.... As I recall, it'...
by Mike_N1JEZ
Fri Mar 09, 2018 11:51 pm
Forum: PowerSDR mRX
Topic: CW in the Pan and Waterfall
Replies: 6
Views: 3382

Re: CW in the Pan and Waterfall

Makes perfect sense. Tnx Scott.
by Mike_N1JEZ
Thu Mar 08, 2018 12:16 pm
Forum: PowerSDR mRX
Topic: CW in the Pan and Waterfall
Replies: 6
Views: 3382

Re: CW in the Pan and Waterfall

I've run into the exact same issue here. I have an ANAN-100 here with vers 3.2 firmware. Running PowerSDR OpenHPSDR mRX PS v3.4.7. I recently noticed that when I transmit CW, I don't see my transmit waveform in the Panafall. I see waveforms when using TUNE and SSB etc. When I key the rig, I get prop...
by Mike_N1JEZ
Sat Jan 06, 2018 3:53 pm
Forum: PowerSDR mRX
Topic: 630m and 2200m support?
Replies: 17
Views: 8850

Re: 630m and 2200m support?

Nice to see a few on 630M. I've been using both a bare Hermes card with Protocol II and Thetis and an ANAN-100 on 630M for a while. On 630M, I use WSJT-X and monitor either WSPR and report spots or JT9. Here's a link to a map from WSPRNet that shows what I was decoding about 8PM EST one evening from...
by Mike_N1JEZ
Wed Nov 15, 2017 11:23 pm
Forum: piHPSDR
Topic: Version 1.2 piHPSDR
Replies: 1
Views: 3730

Re: Version 1.2 piHPSDR

A clean install of piHPSDR fixed everything.

Mike
by Mike_N1JEZ
Wed Nov 15, 2017 11:39 am
Forum: piHPSDR
Topic: Version 1.2 piHPSDR
Replies: 1
Views: 3730

Version 1.2 piHPSDR

I noticed there is a new version of piHPSDR on John's site. Version 1.2 I installed it last night but ran into issues with the GPIO not working as expected. For instance, the tuning knob doesn't work on my controller. Other buttons/knobs are also affected. I'm using a bare Hermes board with Protocol...
by Mike_N1JEZ
Fri Apr 28, 2017 10:52 am
Forum: Protocol 2 Firmware (all radios)
Topic: Hermes Protocol 2 firmware v10.3 released
Replies: 47
Views: 34526

Re: Hermes Protocol 2 firmware v10.3 released

I just loaded firmware 10.3 on my bare Hermes board using KV0S's Web based programmer. It went smoothly and Thetis appears to run fine. My PiHPSDR controller also seems OK. Now for more exhaustive testing.

Mike
by Mike_N1JEZ
Thu Apr 20, 2017 9:27 am
Forum: Hermes Firmware (10 & 100)
Topic: Hermes Protocol 1 firmware: Version 3.2
Replies: 20
Views: 14755

Re: Hermes Protocol 1 firmware: Version 3.2

Scott,

I only remember ever downloading the 'b' version from the Apache Lab site.

Mike
by Mike_N1JEZ
Wed Apr 19, 2017 10:33 am
Forum: Hermes Firmware (10 & 100)
Topic: Hermes Protocol 1 firmware: Version 3.2
Replies: 20
Views: 14755

Re: Hermes Protocol 1 firmware: Version 3.2

I have one of the first batch of ANAN-100's to be delivered and use the 'b' version for exactly that reason. I did install 3.2 to test, but hope the 'b' version comes out soon.

Mike

Go to advanced search