Sorry, typo at the decimal point, should be 72.000 !!!

Hi Tony, unfortunately not. For 4m I am using an internal Transverter for my K3 (made by EA7HG, IF 28MHz) However, I have created a test configuration and checked it with my 7000DLE/ DB6NT 432 MHz transverter (fooling it, HI) - I was able to hear a beacon on 432.473 with the reading of 70.473 MHz - ...

http://www.ha1ya.hu/transverters.htm

73

Volker

DL4ZBG/DK0B

Hi Scott,

thank you so much. Will test it on Wednesday....

73
Volker

Hello Scott,

- when I try to configure the right button "1" you are using als "SQL" on my DJ Console Compact, I get the same ID reply as I get from the right wheel (49). So I cannot use both at the same time. Did you have the same problem?


TNX

Volker

DL4ZBG

Gary,

I did not expect this from the new MKII. I have been suffering from low output/ high IMD (without PS) on 10 an 17m with my 7000 DLE right from the beginning.

Good luck

Volker

I used the XG3 at -73dBm level (S9 on HF) as well. Please bear in mind that the level accuracy of the the XG3 will be in the range of +-1.5dB or so. Good enough.

73
Volker
DL4ZBG

Check the bootloader switch at the bottom of the radio!!

Hello Experts, some external keyers using a winkey chip (e.g. MicroHam) offer the option of generating a ptt signal during transmission. This signal does key the orion board (RX is muted an MOX is visible) BUT seems not to key the PA unit. Somehow strange..... The switching of the PA seem only to be...

Hopefully there will be PIN diode switching available in the next future.....

Volker

DL4ZBG

Has anyone made this mod?

Thanks, Scott this AN is well known. I was just looking for testet values for Rbase, C and perhaps a proposal for the transistor... If Apache Labs modifies the circuitry, there should be updates schematics available, at least for the owners of the "new" version 7000 DLE. I don't want to cr...

Inferring from the information already released it would seem to be the same PA board but with a better heatsink. I do have it on good authority that the fan circuit has been remade in accordance with the fan controller IC manufacturer's app. note, so no more square waves out of the controller. Sco...

Two simple questions:

1) Is the MK II PA board the same as the one used in the 7000 DLE?
2) Is the fan control system the same ("rattlesnake")?

there seems to be the same Molex connector for an external fan.......


TNX

Volker
DL4ZBG

Cecil, https://apache-labs.com/community/viewtopic.php?f=17&t=2682&p=4671&hilit=DIG+2#p4671 Important (extract of my post): BTW: If you want to use DIG2 input for an external keyer (e.g. MicroHam), you have to enable DSP>CW> Checkbox IAMBIC. Took me some time to figure this out... I am u...

Steve,

the SMA Port provides TX output.
Taking a look at the schematics of the PA board you will see that there is no connection/path to the RX switching part.


73

Volker

DL4ZBG/DK0B

1) Yes. But you MUST use stereo plugs, please RTFM
2) left speaker for RX1, right speaker for RX2

https://apache-labs.com/al-downloads/10 ... LOADS.html

73

DL4ZBG

RX Bypass. Please see page 27 of the manual (checkbox "RX bypass on TX"). I am using the XDC-1.

73

Volker

Hello René,

having problems with poor IMD (gain nonlinearity) on two bands (7000DLE) I would like to ask whether you are able to get full power after your mod.

HW?

TNX

Volker

DL4ZBG

Installed the new snubber circuit today. I agree with Phil. It works just like the one described previously.

The Indian Rattlesnake is not tamed but somehow appeased......

Hopefully I have a little more time in the near future to try the internal fan on fixed speed.

73

Volker

DL4ZBG

I have one 4 sale,

incl. 10MHz Daughter Card with TXCO (card not installed)

73

Volker

DL4ZBG

Yes, Scott.

No rattle but the fan is loud at full speed. Abt. 7-8 Volts should be ok while using an external controlled fan. I will check this next time.

Volker

Volker, Not sure if Scott is going to want to move this but - use DIG2 as an external keyer? Why would you put the radio in DIG mode to use it in CW? What am I missing? I DO have a microHAM Keyer II and I was not able to get N1MM+ to work driving the radio on CW ... not sure if this applies or not....

Thanks for the warning, Scott...... Please excuse me for not replying earlier but we weren't celebrating New Year's at home.... I have been using John's "rattlesnake taming circuit" for a few hours without problems, just after I have finished the connection of the 7000 to my MicroHam MK2R+...

Hello Scott,

just tried this mod "on the fly" (did not manage to get the right pins for the fan plug - they will arrive in within a few days). Reduces the "rattling" noise A LOT. Will report next year.

Thanks again

73

Volker

DL4ZBG

Hello Jim,

can you please send me a recording of YOUR 7000 fan noise?

Thanks

Volker

DL4ZBG

Thank you Scott,

I really appreciate your help. I checked all used (known) pins with an ohm meter.

73

Volker

Hello,

in order to get Line Out signals from the breakout board, I was searching for the Orion MK II I/O Pinout (J16? 26 pins?).
Unfortunately, I was not able to find something.... Does somebody have any information regarding this topic?

Thanks

Volker

DL4ZBG

Yes Loren, the impact of the case temperature is noticeable, (almost) regardless of the power level. When you key down the transmitter, the output level rises slightly (abt 0,5 watts at 100W) and then slowly starts to decrease. Same at moderate levels (30 Watts) in almost the same percentage. No pro...

Thanks again, Scott for your recommendations.

I hope that Abhi and his team will find a solution for you cannot leave it as it is unless you don't want to sell it. Many people will read this post.

The hope dies last

73

Volker