It's not just the MODE that is incorrect. The BANDWIDTH display is also incorrect.

As mentioned, the actual operation is okay.

Jamie, W2QO

Hi Scott, If you check the box to turn on the Display,General, Other setting to Small mode/filter on VFOs when you are in DIGU mode with split on what do you see in the VFO B box for the mode and the filter width? Here is what I see: DIGU Capture.PNG It has nothing to do with WSJX-X at all which I h...

Hi Scott, Thanks for the response on the transmit bandwidth. Back to my second question. I am NOT using MultiRX and NOT using RX2. I am simply in ordinary split mode. I am pointing out that VFO B is showing LSB as its mode while VFO A is showing DIGU as its mode. Is that expected behavior in split m...

1. What should the transmit bandwidth be set for in FT-8 using WSJT-X? 2. I have Show mode/filter on VFOs turned on (in Thetis) and when set up for FT8 and VFO A displays DIGU and Var 1. That seems right but VFO B is showing LSB 2.9k right now. Should it be showing DIGU? and if so, how do I change i...

Thanks for the response. OK, I haven't seen the red box since changing to DirectX. Current FPS is 60. It was my distinct impression that there were and are fewer horizontal bursts after changing to DirectX. Would changing the FPS setting lower be of benefit when there is not a red box? Would there b...

Thank you. I have to confess to not knowing about those settings nor of knowing what the red square meant. I have switched to DirectX and the red square went away. Should the change have a favorable effect on the problem I have been experiencing or was it just an unrelated issue you spotted? Again, ...

Hi Mike In Protocol 1, under the Audio Tab, there was Primary, VAC 1 and VAC 2. Primary looked to be some kind of sound card equivalent: Protocol 1 Primary Sound Card Setup.PNG I'm guessing the Protocol 2 equivalent of the Primary Audio is what the TUNE signal travels over and that if there's an aud...

Mike, At this very moment, I am using WSJT-X and so I have the VAC turned back on again. SO: Current VAC audio settings.PNG What is the significance of these audio settings when the VAC audio is OFF and the problem still occurs. There must be something I don't understand if the disabled audio settin...

Mike, Yes, I have a Dell unmanaged gigabit switch with CAT7 double shielded LAN cabling to the 7000 and to the PC. I'm not seeing any positive or negative SEQ errors, so probably no packets lost between the radio and the PC and vice versa. I can however install another Ethernet card and re-configure...

Mike, I'm having the problem with VAC turned off so I guess I don't understand how would changing from MME to Windows DirectSound say affect the use of the Tune button in Thetis with the enable VAC1 checkbox unchecked? In any event I changed from MME to Windows DirectSound and left VAC unchecked and...

The CPU is a W3690

Mike, The Motherboard is an ASRockX58 Extreme3 with a 6-core Xeon W3690 running at 3.466 MHz with Hyperthreading enabled. Wintimertester shows a QPC/GTC ratio of 1.000 after running for several minutes. Forgot to add, the QueryPerformanceFrequency is 14.21818 MHz if that was what you were looking fo...

Mike,

I had to run Process hacker as Administrator to do that but I did it. However the issue continues.

Again thanks for the help.

Jamie, W2QO

Does this indicate an an actual problem with the transmitted signal or a problem monitoring the transmitted signal?

Jamie, W2QO

Mike, Thanks for the quick reply and the help! Only the Tight Loop Latency Test at Dispatch Level showed much higher values on CPU 0and CPU1. (6-core Xeon with Hyperthreading on. I think using Process Hacker to turn off the affinity for CPU0 in Thetis may have reduced the the number of gltches somew...

Have a 7000DLE MKII with 2.0b Protocol 2 firmware and 2.6.9 Thetis. Making contacts with WSJT-X using VAC and seeing horizontal wide glitches in my transmitted signal (Duplex ON). I thought it was a VAC problem but it persisted with VAC (Eugene) and VB-Cables. I assumed it was a VAC cable problem bu...

OK thanks for your assistance.

I am waiting for my vb-audio forum membership to be approved. Then I'll ask there.

73, Jamie W2QO

Yes, that has been the first thing I did upon opening Voicemeeter (or Banana or Potato). If I watch the UMC control panel while making that Hardware Output selection in Voicemeeter the ASIO driver status goes to Active so I know it is not being ignored. The Behringer UMC202HD driver is 4.59.0 by the...

Unfortunately, I had already followed those steps twice before posting. But I did it again today. Uninstall Voicemeeter and UMC202HD, reboot, install, reboot and the end result is the same: no ASIO choice for Hardware Input. There are other choices including the UMC202HD drivers as WDM and MME but n...

I have not been able to either manually select UMC ASIO Driver for hardware input 1 or have it automatically selected. There is no ASIO choice on input even though there is an ASIO: UMC ASIO Driver as a hardware output choice. This is with all audio devices are configured with a 48K sample rate and ...

OK, thanks for looking at it.

73, Jamie 2QO

Here is Version 2.6 Tune with higher power and duplex on.

Looks quite different.

Thank you for the speedy reply.

Here is another shot withDrive set to 20:

Yesterday I upgraded the firmware of my new Black Edition 7000DLE MKII from version 2.4 (Protocol 1) which was installed when I bought it from HRO about a month or two ago. I installed 2.7 using the Bootloader method and everything appeared to be fine. But today I received an email from another oper...

Is there a way to search for VB-Cable in this forum? The hyphen is ignored and VB-Cable is treated as two separate words. Then the VB is ignored because it is only two characters. Putting VB-Cable in quotes doesn't work as the quotes are ignored. Is there a secret to this or is it a case of you can'...