Search found 3063 matches

by w-u-2-o
Sat Jul 24, 2021 9:42 pm
Forum: Angelia Firmware (100D)
Topic: EPCQ128A WITH ANGELIA
Replies: 7
Views: 267

Re: EPCQ128A WITH ANGELIA

Looking at the code, in bootloader.v on line 19 it implies the use of the 128 size parts, and it implies support for the EPCQ128A with the jumper set properly.

I don't understand from the schematic how that can work, but maybe I'm missing something. Maybe I have an old/wrong schematic.
by w-u-2-o
Sat Jul 24, 2021 6:46 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

First stage I think, will be to add a 'visualiser' to the DDC tab, that will show RX1 RX2 PS Diversity and Sync DDC's in use, for both P1/P2 and the various models. Warren has given me some fantastic ddc/adc info from his spreadsheets that he keeps all the wdsp/cmaster/hardware routing. Adding that...
by w-u-2-o
Sat Jul 24, 2021 6:44 pm
Forum: Network Connections & Network Hardware
Topic: Direct Network To 10E
Replies: 3
Views: 57

Re: Direct Network To 10E

Mike, It sounds like you don't know how the IP is configured in the 10E. Therefore, and since it's running protocol 1, I'd suggest you use HPSDR Programmer to explicitly set the IP to 0.0.0.0. This should explicitly configure it for DHCP. Then test it attached to your router. Then try it again with ...
by w-u-2-o
Sat Jul 24, 2021 1:19 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

2) VAC resampler initialisation issues (Scott) The phase margin of the FLL control loop is supercritical, depending on buffersize and samplerate setting. I had to adjust the proportional gain and slew rate in source. The patch below give me stable conditions for my setting (48ksmp,10ms,512bytes). T...
by w-u-2-o
Sat Jul 24, 2021 1:15 pm
Forum: Network Connections & Network Hardware
Topic: Direct Network To 10E
Replies: 3
Views: 57

Re: Direct Network To 10E

Mike, Assuming your 10E was set up for DHCP (the somewhat unintuitive setting of 0.0.0.0 as the initial address using Bootloader or HPSDR Programmer), then address assigned by the router via DHCP is temporary and will be gone every time you power cycle the 10E. So nothing to worry about there. APIPA...
by w-u-2-o
Fri Jul 23, 2021 11:34 pm
Forum: Remote Operation Over The Internet
Topic: Internet Remote using RCFORB and VSPE
Replies: 3
Views: 178

Re: Internet Remote using RCFORB and VSPE

Post screenshots of your Thetis and RCForb CAT setup screens, and of your VSPE settings.
by w-u-2-o
Fri Jul 23, 2021 4:58 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

ATT /S-Att on RX1 works perfekt, on RX 2 still higher Spectrum and S-Meter when I use the Att on RX2 73 Erwin Yes, there is a big problem in there, and always has been. I tried to resolve it last week, but gave up on the idea after the number of issues it caused. I may look at it again at some poin...
by w-u-2-o
Thu Jul 22, 2021 2:15 am
Forum: Remote Operation Over The Internet
Topic: Internet Remote using RCFORB and VSPE
Replies: 3
Views: 178

Re: Internet Remote using RCFORB and VSPE

Dave, I was hoping someone had a RCForb/Thetis cookbook for you, but it appears nobody does, and nor do I. Obviously your cellular connection is the weak link in the chain, with WiFi being the second weakest link the chain. If you want access from your iPhone RCForb is probably your best bet, but yo...
by w-u-2-o
Thu Jul 22, 2021 2:08 am
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Stream Deck with Thetis
Replies: 5
Views: 214

Re: Stream Deck with Thetis

Can you describe a bit more detail about your setup and what it took to enable it to drive CAT commands? Scott - same question to you about the Genovation device. I don't actually use the Genovation device. That's just a frill. I use DDUtil . DDUtil provides for macro buttons . You program them usi...
by w-u-2-o
Mon Jul 19, 2021 3:52 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

On the other hand, Does anyone know it's original intention ("Collapsed"? The original intent of the questionably named "Collapse" mode is to help out folks with small screens get a better view of the spectral display. Collapse mode also forms the basis of the work being done on...
by w-u-2-o
Mon Jul 19, 2021 2:57 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Stream Deck with Thetis
Replies: 5
Views: 214

Re: Stream Deck with Thetis

I do the same thing with DDUtil. I set up macro buttons to do complex tasks. They send CAT to Thetis, and also send commands to my amplifier and to the programmable logic controller (PLC) that runs antenna switching and other station automation tasks. I've not felt the need to have hard buttons, but...
by w-u-2-o
Mon Jul 19, 2021 2:44 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Hate to jump on the PS problem child bandwagon, but there sure seems to be something funny going on. I'm starting to think it is related to the attenuator code, more specifically the step attenuator part of the code. 8000, 21d2, verified fully stable P2 here. So far I've noted the following anomalou...
by w-u-2-o
Sun Jul 18, 2021 2:30 pm
Forum: Angelia Firmware (100D)
Topic: EPCQ128A WITH ANGELIA
Replies: 7
Views: 267

Re: EPCQ128A WITH ANGELIA

That's all the information I have. I don't know how to reconcile the difference between what you see in the code and what is on the schematic. Perhaps someone could look on their factory built Angelia and see what is there. In any case, even if we assume the EPCS128 is the correct part, per the sche...
by w-u-2-o
Sun Jul 18, 2021 1:36 pm
Forum: Microphones, Speakers & Audio Hardware
Topic: How to live stream with headphones on?
Replies: 3
Views: 193

Re: How to live stream with headphones on?

Larry, Remembering your other post this morning where you discussed using the Behringer interface and VAC successfully. So you are halfway there. You just need to get VMP (Voicemeeter Potato) in between. In VMP, put the Behringer ASIO output on output A1. Put the Behringer ASIO mic input (left or ri...
by w-u-2-o
Sat Jul 17, 2021 7:31 pm
Forum: Microphones, Speakers & Audio Hardware
Topic: How to live stream with headphones on?
Replies: 3
Views: 193

Re: How to live stream with headphones on?

Larry, The solution is to use a mixer of some sort to capture both your transmit and receive audio. The mixer will mix/route your microphone audio to both the radio and the streaming software, and do the same in the other direction by mixing/routing your receive audio to your speakers/headphones and...
by w-u-2-o
Sat Jul 17, 2021 3:17 pm
Forum: Angelia Firmware (100D)
Topic: EPCQ128A WITH ANGELIA
Replies: 7
Views: 267

Re: EPCQ128A WITH ANGELIA

The Angelia schematic shows an EPCS64. So at a minimum you probably need to obtain an EPCS64 or an EPCQ64. On the Orion MKII this migration was done mid-stream in production as discussed here: https://apache-labs.com/community/viewtopic.php?f=27&t=3081 The same J14 appears on the Angelia schemat...
by w-u-2-o
Sat Jul 17, 2021 2:17 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Audio recovery
Replies: 3
Views: 192

Re: Audio recovery

Clay, Sorry I didn't reply to this earlier, I was not home all yesterday. Also, I only know two languages: English and Bad English. So you are going to have to carry the load there :) I'm not entirely sure what you mean by "audio recovery", but I'm going to assume you mean something like &...
by w-u-2-o
Thu Jul 15, 2021 8:57 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Waterfall opacity could be a thing if people think it would be worth while. Half opacity in the image. Richie. Negative Nancy votes "No." :D Actually, I don't even understand why people like images in the panadapter portion. I desire the clearest representation of the spectrum possible. I...
by w-u-2-o
Mon Jul 12, 2021 6:50 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Another small bug: when changing the Var 1 or Var 2 filter settings the passband overlay on the spectral display is not updated in a live fashion. You have to click onto another filter preset and then back to see the overlay width update.
by w-u-2-o
Mon Jul 12, 2021 6:48 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Hallo Ritchie and All, I am not shure if this is a bug, or my Mistake: If I start RX 2 and than give with the RX1 S-ATT say 9 db Att, the Gain-line from RX 1 goes up, but on RX 2 the Gain-Line stays but the Noise/Stations in Panadapter goes down?? Also the S-Meter RX 2 goes down. If I use the RX 2 ...
by w-u-2-o
Sat Jul 10, 2021 5:05 pm
Forum: Network Connections & Network Hardware
Topic: TCI Protocol with Apache
Replies: 6
Views: 360

Re: TCI Protocol with Apache

What software supports TCI, not including Sun and Expert's own client software? It seems like TCI is very Sun and Expert specific, and driven hard by Sun in particular to create a Sun-centric standard. Other than that it avoids virtual serial port software, what advantages does it have? I literally ...
by w-u-2-o
Fri Jul 09, 2021 4:48 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Richie, This is just my opinion, but 60M channelization for the US is so simple, I don't mind just clicking 5 times to roll through the entire band. Indeed, I've set up the current version so I see all 5 channels on the panadapter in all 5 60M bandstack entries, so I just watch the passband move fro...
by w-u-2-o
Thu Jul 08, 2021 11:01 pm
Forum: PureSignal Operations (PowerSDR & Thetis)
Topic: PureSignal behaving very strangely on 20 meters on my 7000DLE MKII
Replies: 2
Views: 362

Re: PureSignal behaving very strangely on 20 meters on my 7000DLE MKII

What equipment is in between the ANAN and the dummy load when you get the 20M results that you posted. And were those results into a dummy load?
by w-u-2-o
Wed Jul 07, 2021 10:08 am
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Ernst There is no way for Richie to do that. The FPGA receives no signal that tells it what the source of the 10MHz is so the firmware can not know and therefore the software can not know either. The circuit that automatically selects the source of the 10MHz reference lies completely outside of the ...
by w-u-2-o
Wed Jul 07, 2021 12:07 am
Forum: Microphones, Speakers & Audio Hardware
Topic: Powered Speaker for my setup !!
Replies: 61
Views: 16151

Re: Powered Speaker for my setup !!

Check your PM, please.
by w-u-2-o
Tue Jul 06, 2021 1:08 pm
Forum: Microphones, Speakers & Audio Hardware
Topic: Powered Speaker for my setup !!
Replies: 61
Views: 16151

Re: Powered Speaker for my setup !!

Using power studio monitors is an amazing difference compared to even the priciest "ham radio" or "communications" speakers, isn't it? :) Given that the speakers, and cable, work 100% in other equipment, that would mean that the 3.5mm headphone jack on the ANAN is either faulty o...
by w-u-2-o
Mon Jul 05, 2021 5:54 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

There is active peak hold time but not decay time. At the moment after configurable hold time (in setup) they decay at an ever increasing dBm rate. I could put in a dbm/second thing, but if we just use a fixed 2 second decay for example, peaks that were very high would look as if they were falling ...
by w-u-2-o
Mon Jul 05, 2021 12:39 pm
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Hi Richie, Understood on the getPixel flag. Will just watch and see. I always have vsync enabled and run 30Hz to match my (slow) 4K displays. I use Prio to save process priorities in Task Manager and set Thetis to "realtime". BREAK Some thoughts on the cool new display features (obviously ...
by w-u-2-o
Mon Jul 05, 2021 1:54 am
Forum: Thetis
Topic: Thetis v2.8.11 - current issues
Replies: 571
Views: 16189

Re: Thetis v2.8.11 - current issues

Richie,

Any advice on what to do/not do if you are seeing bursts of yellow square GetPixel warnings?

Thanks,

Scott
by w-u-2-o
Mon Jul 05, 2021 1:40 am
Forum: Digital Mode, Rig Control & Logging Software
Topic: Anan 10E PTT Out Only Working with Front Panel Mic PTT
Replies: 6
Views: 207

Re: Anan 10E PTT Out Only Working with Front Panel Mic PTT

I think I've got it sorted for you: you are using the wrong pin on the accessory connector as PTT OUT. It seems like you are using the PTT IN pin, which is in parallel with the mic PTT signal. You need to use the correct pin for PTT OUT. Take a look at the schematic here: https://apache-labs.com/com...

Go to advanced search