Search found 5569 matches
- Wed Apr 17, 2024 11:00 am
- Forum: Apache-specific Hardware Discussions
- Topic: Usefulness of A-10 TAPR upgrade/accessories?
- Replies: 2
- Views: 132
Re: Usefulness of A-10 TAPR upgrade/accessories?
Wow, I'm surprised these can still be purchased! I don't have an ANAN-10, but I do have a 100D and it also required a similar modification for good PureSignal performance. I built my own version. IMHO the TR-Plus is a worthy accessory. It's definitely necessary for PureSignal because the older desig...
- Wed Apr 17, 2024 10:48 am
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: How to ground Anan A-10E?
- Replies: 1
- Views: 126
Re: How to ground Anan A-10E?
Yep, put a lug under a screw is pretty much all you can do. Or you can add your own ground lug.
If you want to get super serious about grounding you can also go through the exercise of removing any paint on the case where the ends meet the main extrusion so that there is good contact between the two.
If you want to get super serious about grounding you can also go through the exercise of removing any paint on the case where the ends meet the main extrusion so that there is good contact between the two.
- Tue Apr 16, 2024 7:07 pm
- Forum: Thetis
- Topic: Automatic ID feature built into Thetis
- Replies: 15
- Views: 767
Re: Automatic ID feature built into Thetis
That's a good SSB solution as long as the ID is issued reasonably close to the 10-minute marker in the queue. Even if the timer is queued, it may require waiting well beyond ten minutes to ID after a long-winded op finishes. That's what I meant by "spirit of the law". If you are in a long...
- Tue Apr 16, 2024 3:23 pm
- Forum: Thetis
- Topic: Automatic ID feature built into Thetis
- Replies: 15
- Views: 767
Re: Automatic ID feature built into Thetis
I'm with Gary on this. ID should not transmit at a time of it's own choosing. Perhaps the solution to this is to simply queue up an ID for transmission and indicate to the operator an ID is pending. Then the next time the operator transmits the ID will be transmitted. IMHO that would be good enough,...
- Sun Apr 14, 2024 1:47 pm
- Forum: Thetis
- Topic: Automatic ID feature built into Thetis
- Replies: 15
- Views: 767
Re: Automatic ID feature built into Thetis
That's not an automatic ID feature. It's an ID reminder feature. Nothing is played over the air.
- Wed Apr 10, 2024 8:29 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: Protocol 2.2.2 link
- Replies: 4
- Views: 273
- Wed Apr 10, 2024 5:48 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: Protocol 2.2.2 link
- Replies: 4
- Views: 273
Re: Protocol 2.2.2 link
Which model ANAN is the firmware for?
- Wed Apr 10, 2024 5:47 pm
- Forum: Digital ("Virtual") Audio
- Topic: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
- Replies: 9
- Views: 657
Re: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
Thanks Scott, If I can run all digital on the same line that aoulçd be good (I suppose that only one program at the time, if I want to run Winrabler for RTTY, I must close WSJT-x or JTDX or MSHV, and the opposite also). From a purely audio perspective all these app's can run at the same time on the...
- Wed Apr 10, 2024 2:35 pm
- Forum: Digital ("Virtual") Audio
- Topic: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
- Replies: 9
- Views: 657
Re: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
So for Winwrabler, I just choose the Input as Voicemeeter AUX Input And for output Voicemeeter Out B3 Then Send B1 to B3 and B3 to B1 Correct. One mistake. If you wish to use strip B3 "Voicemeeter VAIO3" for Winwarbler then... For input choose Voicemeeter VAIO3 Input. The rest is correct....
- Tue Apr 09, 2024 11:13 am
- Forum: Digital ("Virtual") Audio
- Topic: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
- Replies: 9
- Views: 657
Re: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
Nuno, Now that you've apparently got WSJT-X working, the rest is easy. Voicemeeter will happily allow more than one application to share a channel strip if they are not using ASIO. Since none of the digi mode app's use ASIO, you can simply set them all up like WSJT-X and run them all on channel stri...
- Mon Apr 08, 2024 10:17 am
- Forum: G2 Operating System & Applications
- Topic: G2 power supply - TAKE CARE!
- Replies: 6
- Views: 413
Re: G2 power supply - TAKE CARE!
So the problem had nothing to do with the G2 itself. It's seems simply a coincidence. It was difficult to imagine how running at 12.9V could cause any problems.
- Sun Apr 07, 2024 9:13 pm
- Forum: Network Connections & Network Hardware
- Topic: Problem changing IP Adresse
- Replies: 2
- Views: 335
Re: Problem changing IP Adresse
Do you know if the unit is running Protocol 1 or Protocol 2 firmware? Knowing the answer to that will help determine whether you proceed with Programmer or Bootloader.
- Sun Apr 07, 2024 9:11 pm
- Forum: Digital ("Virtual") Audio
- Topic: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
- Replies: 9
- Views: 657
Re: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
Looks pretty good so far. First, a couple of clean up items: - Remove the input selection assignments on Voicemeeter channel strips A1, A2 and A3 (the first three strips). We'll come back to that later. - Remove all of the assignments on channel strip B3, marked "Voicemeeter VAIO3". Now fo...
- Sun Apr 07, 2024 2:09 pm
- Forum: Digital ("Virtual") Audio
- Topic: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
- Replies: 9
- Views: 657
Re: Hermes Lite, Thetis, UMC 202HD, VM Potato and WSJT no audio
That it's an HL2 does not matter. Let's take this one step at a time. Part of the problem is that Voicemeeter naming conventions can be confusing. Step one, get audio moving out of Thetis, through Voicemeeter, to the UMC202. - Your choice of UMC ASIO for Hardware Out A1 is correct. - Set Thetis to u...
- Sun Apr 07, 2024 12:09 pm
- Forum: Thetis
- Topic: Thetis 2.0.3.6 dev_2 issues
- Replies: 13
- Views: 2253
Re: Thetis 2.0.3.6 dev_2 issues
There's a lot of setup screens, that's for sure! Don't forget that you can almost always find the appropriate setup tab by right clicking on the control in question. This definitely works with AGC, give it a try! The new "Finder" menu is also helpful. See what you get when you put in "...
- Sun Apr 07, 2024 12:07 pm
- Forum: G2 Operating System & Applications
- Topic: G2 power supply - TAKE CARE!
- Replies: 6
- Views: 413
Re: G2 power supply - TAKE CARE!
It's not entirely clear from your post, but: - Did the Pi crash during this power supply event? or - When you saw the voltage had dropped and you "completely shut down the station within a few seconds" did you follow the proper shutdown procedure so that the Pi was not just crashed off? Be...
- Sun Apr 07, 2024 12:04 pm
- Forum: Sales, Delivery, Warranty & Repair Discussions
- Topic: There is no such thing as an ANAN-7000DLE MKIII
- Replies: 10
- Views: 4725
Re: There is no such thing as an ANAN-7000DLE MKIII
From a user standpoint, and using Thetis as the software, the only practical advantage the G2 has over the 7000 is that the G2 has a complete and fully stable implementation of Gigabit Ethernet. The RF and DSP architectures are otherwise essentially identical, with differences only measurable on a t...
- Thu Apr 04, 2024 1:37 pm
- Forum: Thetis
- Topic: Thetis 2.0.3.6 dev_2 issues
- Replies: 13
- Views: 2253
Re: Thetis 2.0.3.6 dev_2 issues
2.10.3.6 (1/28/24) dev_2, correct? There is no user adjustment for the red line. Warren, Richie and I proved that it is mathematically correct, regardless of how it may look to some. IMHO it is spot on. Indeed, Richie's algorithm for calculating it is incredibly elegant, working for nearly any set o...
- Wed Apr 03, 2024 11:48 am
- Forum: PureSignal Operations (PowerSDR & Thetis)
- Topic: G-2 Screen Model
- Replies: 5
- Views: 519
Re: G-2 Screen Model
I still don’t fully understand pure signal I read it but have not seen it -I guess it’s like a good clean compression of your audio PureSignal is not an audio processing facility. It is not a voice compressor. It is a method for significantly reducing intermodulation distortion (IMD) in your signal...
- Wed Apr 03, 2024 1:48 am
- Forum: PureSignal Operations (PowerSDR & Thetis)
- Topic: G-2 Screen Model
- Replies: 5
- Views: 519
Re: G-2 Screen Model
My G-2 screen model on pre order I have Question. PowerSDR /Pure-Signal is this available using my G-2 as stand alone with out using WIFi or computer Yes. The piHPSDR client should come preloaded on the G2 and it supports PureSignal. My Yaesu FTDX 101D had new feature like pure-signal it was a real...
- Tue Apr 02, 2024 12:04 pm
- Forum: Apache Labs News
- Topic: Shipping Updates
- Replies: 246
- Views: 315220
Re: Shipping Updates
Thanks for posting that, David!
I can't understand why Apache doesn't post those things here in the forum
I can't understand why Apache doesn't post those things here in the forum
- Tue Apr 02, 2024 12:01 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: Microphone/ Audio Interface Options
- Replies: 74
- Views: 35771
Re: Microphone/ Audio Interface Options
Bob--your post here and your other post that I answered represent a unique set of problems that don't fit neatly into either of the topics you tailed onto. Don't be shy! :) Please start your very own new topic in the Digital Virtual Audio sub-forum (https://community.apache-labs.com/viewforum.php?f=...
- Tue Apr 02, 2024 11:56 am
- Forum: Thetis
- Topic: Changing Windows 10 Network Throttling Index for Better Performance
- Replies: 37
- Views: 50467
Re: Changing Windows 10 Network Throttling Index for Better Performance
Bob, It seems there are at least two things going on here. First is the lack of the expected registry keys. This might affect dropout performance but not "hooting and feedback". You might need some Windows OS repairs. Try running the following commands from an Command Prompt (Admin) window...
- Mon Apr 01, 2024 7:39 pm
- Forum: Microphones, Speakers & Audio Hardware
- Topic: TX audio - Rack gear to Anan G2 interface questions
- Replies: 8
- Views: 748
Re: TX audio - Rack gear to Anan G2 interface questions
You attributed quotes to me that I did not make. I am such an idiot. You have my abject apology. What happened was when I went to quote your post and respond to it I accidentally clicked the edit button instead of the quote button and blithely started typing. And, because I am a moderator, the syst...
- Sun Mar 31, 2024 11:18 am
- Forum: Apache Labs News
- Topic: ANAN-G2 Shipping Update
- Replies: 272
- Views: 3093468
Re: ANAN-G2 Shipping Update
Order Number: AC-4290 Joseph Conover I ordered G2 Screen model 14 days ago with $1000 down payment (PayPal)was told 3-4 week delivery time that was two weeks ago - Should I cancel my order or wait Joe KA2ZSD I would recommend waiting. My understanding is that Paypal disputes can be opened up any ti...
- Sat Mar 30, 2024 1:20 am
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: "Conflict" between TCI and TCP?
- Replies: 9
- Views: 362
Re: "Conflict" between TCI and TCP?
AFAIK baud rate does not matter with virtual cables.
- Fri Mar 29, 2024 11:34 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: "Conflict" between TCI and TCP?
- Replies: 9
- Views: 362
Re: "Conflict" between TCI and TCP?
Great catch!
- Fri Mar 29, 2024 7:50 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: "Conflict" between TCI and TCP?
- Replies: 9
- Views: 362
Re: "Conflict" between TCI and TCP?
It would probably be best to use the default ports.
- Fri Mar 29, 2024 6:00 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: "Conflict" between TCI and TCP?
- Replies: 9
- Views: 362
Re: "Conflict" between TCI and TCP?
You've got quite a train wreck going on there! Everything is interfering with everything else because you are using the same ports everywhere. You can't use the same port for both TCI and TCP. Make them different in Thetis. Adjust your other software and hardware as necessary to match your selection...
- Fri Mar 29, 2024 11:44 am
- Forum: Digital ("Virtual") Audio
- Topic: How to UMC204HD>Voicemeeter>LightHost>Thetis
- Replies: 5
- Views: 409
Re: How to UMC204HD>Voicemeeter>LightHost>Thetis
This is probably going to do more harm than good :D I use Voicemeeter Potato strictly as a patch bay between the audio interface (Presonus Studio 192 Mobile), Thetis (via cmASIO), digi mode software and Reaper (DAW). All mixing and routing is done in Reaper. Mic's and speakers are plugged into the P...