Had to delete the OpenSDR in my AppsData folder

Once I did that - reinstalled, no issues now.

Its been months since I have used my rig. I had to rebuild my PC and started from scratch. I installed 2.9 Thetis. (have protocol 2 already installed working fine).

However, It will NOT connect if I select ANAN-7000DLE. It WILL connect on HERMES or others.

Any ideas?

I admit, I could be wrong - but did enabling the attenuator RAISE the noise floor measurements (ie pan adapter and S meter) happen in previous versions?
I have auto AGC off.

73
Mike
WA2COP

These videos were fantastic! Thanks for sharing I compare my FTDX101D to the Anan constantly and yes the Anan NR2 when its a big signal, sounds amazing, but for weaker signals the 101D really outshines it when it comes to NR (only). Are there any suggestions how to better "tune" the NR par...

Thanks! The workaround worked! When ever clicking or off VAC2 ONLY WHEN RX2 is enabled, for what ever reason it ALWAYS goes to 40 meters no matter what band I am on. As you can imagine, its extremely annoying. Not sure if this is reproducible for all of you!. ok there is an issue when SD (stereo div...

Thanks for looking into this! Thetis_database_export_1-16-2022_3.11 PM.xml When ever clicking or off VAC2 ONLY WHEN RX2 is enabled, for what ever reason it ALWAYS goes to 40 meters no matter what band I am on. As you can imagine, its extremely annoying. Not sure if this is reproducible for all of yo...

I went the Macro Button as you suggested. I set it up to Disable B1 and MUTE the MIC and ENABLE B1 on the Virtual Input for DIGITAL and then for VOICE remove the MUTE, Enable B1 on the MIC and DISABLE B1 on the virtual input. Would be a nice enhancement if you can "Execute a script" on mod...

When ever clicking or off VAC2 ONLY WHEN RX2 is enabled, for what ever reason it ALWAYS goes to 40 meters no matter what band I am on. As you can imagine, its extremely annoying.

Not sure if this is reproducible for all of you!.

Yes

Thanks

w-u-2-o wrote:Is your mic audio going through Voicemeeter?

I use both voice and digital regularly and flip between. However, for me to do this effectively I need to change a few settings around every time. I don't mind staying thetis but having to open up VoiceMeter is a pain. Is there a way for me to when I am in JTDX route those transmit channels and excl...

ok I found the issue - I had EQ set in VoiceMeter Banana which was driving up the gain above zero. All is good. I have also made some of the changes you suggested and am able to control via the AGC vs everything else. Thanks again!

You may want to move this to VAC section.

ok you both gave me a ton to think about - I will adjust accordingly and report back. thanks as always for the support! This would appear to be two separate problems. 1) as @kc2rgw pointed out, you should never be experiencing clipping at the input of your audio device. That means the audio level ou...

I would like to know if there is a way to limit the maximum gain applied to the AGC minimize clipping on the input of my Audio Device on overly strong signals. I am constantly adjusting the volume (ie RX AF Gain ).

Any suggestions?

Thanks for investigating. I played around and here is the best I could get from VAC2. My VAC1 is VERY lower latency as you can see (MOTU Audio device is fantastic!)... T0 equalize voice I would need to raise VAC1 Buffer to 2048 AND increase some of the other latency settings. :lol: Unfortunately wit...

Thanks.. got it all working with your suggestions. However the only way I could sync the audio (ie remove the echo) was to add a a fair amount of latency to vac1 (adjusting the various parameters) Any other suggestions? Your approach is spot-on: using a separate virtual channel in Voicemeeter for VA...

I am pulling my hairs being able pump VAC2 for RX2 into my audio device through voicemeter banana. I have been using VoiceMeter Banana for some time now with success for my MAIN. Now that I have that fully configured and working wonderfully I am having a hell of a time to get it working for VAC2. An...

w-u-2-o wrote:Just remember, until you terminate all your inputs on the back of the ANAN, don't be too quick to blame a spur on an internal source.

Its on order! Will report back!... Also long ethernet cable to get it away from my other equipment.

Thank you for the support!

Having the same issue

Thank you for the detail reply. I did some more digging and found Diversity was enabled which based on the past setting was attentuating the main receiver. When I would flip my receive antenna on it would normalize the signal. Thus why I perceived an increase in noise. My mistake. Regarding the spur...

RX2 Isolation Question: I noticed this radio does NOT have much isolation from ANT1 AND RX2 antenna ports. I have physical switches on both my Main Antenna and my Receive Only Antenna, both plugged into the appropriate ports on the radio. When I switch OFF my main antenna and have my receive antenna...

Thank you again. Makes perfect sense!

Much appreciated!

Thank you sir for the detailed explanation and fantastic read!
Am I mistaken by your statement (" It is merely changing how noise power is displayed,") but is the sampling rate only affecting the visual aspects of reception? Are there no other benefits?

Not sure if this the correct forum / category - move to the proper. I have a fundamental question being a new user to SDR in general. I have noticed that the noise floor or noise in general increases with the higher sampling rate. This makes sense to me since its increasing the spectrum bandwidth. H...

Does this show up with the antenna unplugged?

If so it’s the power supply or something near field

If it’s with the antenna plugged something far field most likely

Thank you!

What does the red dot in the upper left above the dB numbers indicate. It flashed on and off a few times.
See attachment.
Thanks

Hi All, I noticed my bootloader switch does not go all the way and doesn't seat positively. Is there a way to test the switch without actually doing a firmware update? I have protocol 2 already installed using the programmer however, I want to fix the switch if it is an issue sooner than later in th...