Search found 9 matches
- Mon Jul 05, 2021 8:44 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Anan 10E PTT Out Only Working with Front Panel Mic PTT
- Replies: 6
- Views: 2708
Re: Anan 10E PTT Out Only Working with Front Panel Mic PTT
Thanks Scott, that was the problem. Looking at the back of the 10E, I was using the bottom left-hand most "pin1" on the left side of the table AND the red pin number assignments in the User Guide. Reading table numbers on the right side indicated "pin 25" which per the red number...
- Sun Jul 04, 2021 11:13 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Anan 10E PTT Out Only Working with Front Panel Mic PTT
- Replies: 6
- Views: 2708
Re: Anan 10E PTT Out Only Working with Front Panel Mic PTT
With nothing in the front panel TUN, MOX, CAT, CAT+PTT still key the 10E but not PTT out. I also noticed today keying CW will key the 10E but not PTT out.
- Sun Jul 04, 2021 4:21 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Anan 10E PTT Out Only Working with Front Panel Mic PTT
- Replies: 6
- Views: 2708
Re: Anan 10E PTT Out Only Working with Front Panel Mic PTT
Firmware 1.5, OpenHPSDR mRX PS v3.4.8
No, TUN, MOX, CAT, CAT+PTT do not key PTT out, but front panel MIC PTT does as before.
No, TUN, MOX, CAT, CAT+PTT do not key PTT out, but front panel MIC PTT does as before.
- Sat Jul 03, 2021 7:23 pm
- Forum: Digital Mode, Rig Control & Logging Software
- Topic: Anan 10E PTT Out Only Working with Front Panel Mic PTT
- Replies: 6
- Views: 2708
Anan 10E PTT Out Only Working with Front Panel Mic PTT
Running Anan 10E, Thetis 2.8.11, Firmware 10.3, Protocol 2, Windows10 fully updated... I am unable to make PTT out, pin 1 of accessory connector, activate on anything other than mic PTT from front panel. PTT out will not activate using, for example, Tune, MOX, and most importantly CAT or CAT/PTT fro...
- Tue Jun 22, 2021 7:06 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 10E SMA RX Reception OK, main BNC Reception Intermittent - Fixed
- Replies: 7
- Views: 3597
Re: 10E SMA RX Reception OK, main BNC Reception Intermittant
This 10E is now working properly. Doug, W5WC, found an intermittent ribbon cable and replaced the cable and connectors. The 10E has not had a single sensitivity dropout since. Thanks Doug!
- Thu Jun 03, 2021 7:36 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 10E SMA RX Reception OK, main BNC Reception Intermittent - Fixed
- Replies: 7
- Views: 3597
Re: 10E SMA RX Reception OK, main BNC Reception Intermittant
Scott, many thanks for your very helpful detailed response. I appreciate the time you took to compose it. Because I am not sure relay replacement will be the only thing required, and not having real steady hands nor the best vision, I just sent the 10E to Doug who graciously agreed to take a look at...
- Thu May 27, 2021 7:32 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 10E SMA RX Reception OK, main BNC Reception Intermittent - Fixed
- Replies: 7
- Views: 3597
Re: 10E SMA RX Reception OK, main BNC Reception Intermittant
Thanks for the schematic accuracy assurance. Giving the PA board more study I realized my mistake was thinking RX IN was the SMA RX input, and looking at it that way the receive paths made no sense. It dawned on me RX IN has to be PA board output to main board, then I spotted J3 jumper termination. ...
- Sun May 23, 2021 12:03 am
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 10E SMA RX Reception OK, main BNC Reception Intermittent - Fixed
- Replies: 7
- Views: 3597
Re: 10E SMA RX Reception OK, main BNC Reception Intermittant
Thanks for the link but it seems to point to the same two schematics I have seen and referred to in my message, why I asked for any others out there. Neither clearly helps me to answer my question of why RX input always works but BNC inputs have a problem. One schematic deals mostly with TX configur...
- Sat May 22, 2021 9:04 pm
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 10E SMA RX Reception OK, main BNC Reception Intermittent - Fixed
- Replies: 7
- Views: 3597
10E SMA RX Reception OK, main BNC Reception Intermittent - Fixed
Community, My 10E has a problem where SMA RX reception is always normal. However, reception using any main BNC input occasionally acts like antenna was suddenly disconnected. A momentary band change or MOX toggle will restore normal BNC reception for awhile. The problem happens more frequently when ...