Search found 26 matches

by nubbyless
Mon Oct 25, 2021 7:06 pm
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - UPDATES and current issues

For the the amp view issue I would suggest unchecking low res bottom right in your screenshot and see if that helps.
by nubbyless
Wed Oct 13, 2021 2:08 am
Forum: PowerSDR mRX
Topic: Anyone tried using W11 w 3.4.9
Replies: 5
Views: 5483

Re: Anyone tried using W11 w 3.4.9

Works here with win11
by nubbyless
Mon Sep 27, 2021 11:05 pm
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - current issues

Hi I updated the video driver and rebooted no change it seems if I'm set at 250% and it's not acting right I can drag it to my other monitor and then back and it corrects also if I set waterfall update to 1 it clears up I normally run it set at 2 if I place it back to 2 the jiggling and pixelalatin...
by nubbyless
Mon Sep 27, 2021 10:57 am
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - current issues

Hi I updated the video driver and rebooted no change it seems if I'm set at 250% and it's not acting right I can drag it to my other monitor and then back and it corrects also if I set waterfall update to 1 it clears up I normally run it set at 2 if I place it back to 2 the jiggling and pixelalating...
by nubbyless
Mon Sep 27, 2021 12:00 am
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - current issues

Hi Just went from the last J version to the most recent K version and now my display waterfall and panadapter is very pixelated and jittering unless i run windows scale at 300% also frame rate and left side scale are off the display at 250% scaling i always ran it at 250% and it was fine. The montio...
by nubbyless
Fri Sep 24, 2021 6:51 am
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - current issues

Do the changes effect the Open-drain PTT output for the amplifier or just the standard user controlled pins 0 thru 6


Thanks
Fred
by nubbyless
Sun Jul 18, 2021 4:04 pm
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - current issues

Hi I have anan 10e I can do some test with any particular thing I should look for with the new ADC setup

Fred
W4yny
by nubbyless
Mon Jul 12, 2021 10:55 pm
Forum: Thetis
Topic: Thetis v2.8.11 - UPDATES and current issues
Replies: 1752
Views: 874781

Re: Thetis v2.8.11 - current issues

With my 10e I understand thetis with pure signal is unreliable with protocol 2 and this is a firmware issue. I would be happy to run thetis with protocol 1 with my 10e but when pure signal and dup are activated on thetis protocol 1 the dup screen freezes on transmit I'm not sure if this is a firmwar...
by nubbyless
Sun Feb 28, 2021 4:17 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Anan 10 output power
Replies: 0
Views: 2123

Anan 10 output power

Hi just a question for any anan 10 or 10e owners what is your maximum output power mine maxes out at 14watts on 80m with calibration spinner all the way down 10m maxes out at about 8 watts spinner all the way down I'm reading on an lp-100a into a dummy load I have read it should max out at about 20 ...
by nubbyless
Fri Feb 12, 2021 12:42 am
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 232
Views: 232263

Re: Thetis 2.8.11 Released!

Just for reference The dup screen on my 10e does not work with protocol 1 either i had posted about this some time back.
It does work fine with protocol 2 but with protocol 2 i must run manual calibration as pure signal auto calibrate is unreliable on the 10e with protocol 2.
by nubbyless
Tue Jan 19, 2021 1:17 am
Forum: Apache Labs Radios: Buy/Sell/Trade
Topic: For sale Anan-100 16 bit
Replies: 2
Views: 2956

Re: For sale Anan-100 16 bit

Is it still for sale can you ship to us
by nubbyless
Sun Jan 10, 2021 12:35 am
Forum: Apache Labs Radios: Buy/Sell/Trade
Topic: Looking for anan 10 or 10e
Replies: 0
Views: 2289

Looking for anan 10 or 10e

looking to buy and anan 10 or anan 10e in good working order or might consider a 100 or 100b for the right price
by nubbyless
Sun Jan 10, 2021 12:33 am
Forum: Apache Labs Radios: Buy/Sell/Trade
Topic: Hermes 10 Setup for Sale
Replies: 1
Views: 2071

Re: Hermes 10 Setup for Sale

is this still for sale
by nubbyless
Fri Oct 30, 2020 3:36 pm
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 232
Views: 232263

Re: Thetis 2.8.11 Released!

Thanks for the update! I'm running the latest Thetis 2.8.11 x64 version. Everything seem to be working fine for me on my Anan 100B running protocol 2 firmware 10.3, except PureSignal runs very unstable, unreliable and distorted compared to protocol 1. I did revert to protocol 1 firmware and can con...
by nubbyless
Thu Oct 22, 2020 5:01 am
Forum: Protocol 2 Firmware (all radios)
Topic: 14-bit Hermes (10E and 100B) Protocol 2 Firmware Topic
Replies: 17
Views: 22451

Re: P2 version 10.3 released for 14-bit Hermes (10E and 100B)

Has there been any further development on this firmware it works with the latest thetis but pure signal seems unreliable sometimes works sometimes doesn't
by nubbyless
Wed Oct 21, 2020 11:16 pm
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 232
Views: 232263

Re: Thetis 2.8.11 Released!

Thanks for the new update most of the problems on my Anan 10e have now been solved. But i still have a pure signal issue if i run pure signal with dup on in protocol 1 pure signal seems to be working but the pan adapter freezes on transmit and returns when in rx i still don't know if this is just a ...
by nubbyless
Fri Oct 16, 2020 11:23 am
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 232
Views: 232263

Re: Thetis 2.8.9 Released!

My anan 10e behaves the same with #5 this on p1 and p2 as well. RE:Thetis v2.8.9 x64 on ANAN 10 P1 potential issues I do confirm ANAN 10 selection Acknowledged #1 and # as already known issues #3 after importing the TX profile used on PSDRmrx, did not perform any save, everything fine now, that has ...
by nubbyless
Tue Oct 13, 2020 10:47 pm
Forum: Thetis
Topic: Thetis 2.8.11 Released!
Replies: 232
Views: 232263

Re: Thetis 2.8.9 Released!

Running 2.8.9 64 bit with anan 10e Protocol 1 with the tapr pure signal relay board and xtronic coupler. i do not get any type of triggering or attenuator calibration its like pure signal is not working at all i tested in 3.4.9 powersdrmrx and its still working fine there. EDIT UPDATE: I had the rad...
by nubbyless
Tue Sep 29, 2020 5:14 pm
Forum: PowerSDR mRX
Topic: Some Thoughts On Asymmetry, Symmetry, and Using Pure Signal When Running AM With The ANAN
Replies: 2
Views: 4651

Re: Some Thoughts On Asymmetry, Symmetry, and Using Pure Signal When Running AM With The ANAN

I know this is an older post but has openhpsdr changed since this was posted? I notice my carrier setting goes up to 125 and when it is set at 100 according to my rea monitor it breaks 100% negative easily I need to push up to a setting of at least 108 then I see 120 positive and can not break past ...
by nubbyless
Sat Sep 05, 2020 8:45 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Anan 10e fpga heatsink size
Replies: 3
Views: 2571

Re: Anan 10e fpga heatsink size

thanks i searched and searched google and never found it i assumed if it was here i would of seen it in a google search but i was wrong sorry about that. But after looking at that schematic it shows the ALTERA EP3C40Q240 which i believe is in the anan 10 not the 10e. although it may be the same size...
by nubbyless
Sat Sep 05, 2020 2:25 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Anan 10e fpga heatsink size
Replies: 3
Views: 2571

Anan 10e fpga heatsink size

Hi does any one know of a schematic for the 10e so I can look up the exact fpga size I know it's a EP3C25 but there seems to be several packages I would like to add a stick on heatsink to it. I have seen some pictures where people have done this maybe someone knows what size I should purchase. Thank...
by nubbyless
Wed Sep 02, 2020 9:54 pm
Forum: PureSignal Operations (PowerSDR & Thetis)
Topic: Is it ok to run pure signal at 384k with Anan 10E ?
Replies: 2
Views: 3274

Re: Is it ok to run pure signal at 384k with Anan 10E ?

ok thanks ill test it for a while and see how it goes
by nubbyless
Wed Sep 02, 2020 9:09 pm
Forum: PureSignal Operations (PowerSDR & Thetis)
Topic: Is it ok to run pure signal at 384k with Anan 10E ?
Replies: 2
Views: 3274

Is it ok to run pure signal at 384k with Anan 10E ?

Hi i have my Anan 10E and blf188xr mosfet amplifier up and running with pure signal using the xtronic sampler and the tr-plus tapr board. It seems to be working well i am only running at 192khz i thought i read somewhere that was as high as you can run with pure signal. Can i run it at 384k it seems...
by nubbyless
Sat Aug 29, 2020 4:23 am
Forum: SDR Console
Topic: anan 10E rear line in for microphone
Replies: 2
Views: 5129

Re: anan 10E rear line in for microphone

Thanks I tried that before posting but it didn't seem to work
by nubbyless
Wed Aug 26, 2020 5:27 pm
Forum: Protocol 2 Firmware (all radios)
Topic: New -10/-100 16-BIT Hermes Protocol 2 Firmware Topic
Replies: 124
Views: 151781

Re: New -10/-100 16-BIT Hermes Protocol 2 Firmware Topic

Hi not trying to hijack your thread but curious how to modify k19 for pure signal can I just seperate the via trace to ground then feed in sample through Rx port? I tried the 50ohm resistor in series with Rx port and my xtronic sampler does not send enough signal to use it this way and I would rathe...
by nubbyless
Fri Jul 24, 2020 2:30 pm
Forum: SDR Console
Topic: anan 10E rear line in for microphone
Replies: 2
Views: 5129

anan 10E rear line in for microphone

Is there a way in sdrc v3 to set the rear line in as the microphone I have selected microphone on radio but I believe this only uses the front mic input

Thanks
Fred w4yny

Go to advanced search