Search found 10 matches

by nubbyless
Fri Oct 16, 2020 11:23 am
Forum: Thetis
Topic: Thetis 2.8.9 Released!
Replies: 131
Views: 5551

Re: Thetis 2.8.9 Released!

My anan 10e behaves the same with #5 this on p1 and p2 as well. RE:Thetis v2.8.9 x64 on ANAN 10 P1 potential issues I do confirm ANAN 10 selection Acknowledged #1 and # as already known issues #3 after importing the TX profile used on PSDRmrx, did not perform any save, everything fine now, that has ...
by nubbyless
Tue Oct 13, 2020 10:47 pm
Forum: Thetis
Topic: Thetis 2.8.9 Released!
Replies: 131
Views: 5551

Re: Thetis 2.8.9 Released!

Running 2.8.9 64 bit with anan 10e Protocol 1 with the tapr pure signal relay board and xtronic coupler. i do not get any type of triggering or attenuator calibration its like pure signal is not working at all i tested in 3.4.9 powersdrmrx and its still working fine there. EDIT UPDATE: I had the rad...
by nubbyless
Tue Sep 29, 2020 5:14 pm
Forum: PowerSDR mRX
Topic: Some Thoughts On Asymmetry, Symmetry, and Using Pure Signal When Running AM With The ANAN
Replies: 2
Views: 2087

Re: Some Thoughts On Asymmetry, Symmetry, and Using Pure Signal When Running AM With The ANAN

I know this is an older post but has openhpsdr changed since this was posted? I notice my carrier setting goes up to 125 and when it is set at 100 according to my rea monitor it breaks 100% negative easily I need to push up to a setting of at least 108 then I see 120 positive and can not break past ...
by nubbyless
Sat Sep 05, 2020 8:45 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Anan 10e fpga heatsink size
Replies: 3
Views: 366

Re: Anan 10e fpga heatsink size

thanks i searched and searched google and never found it i assumed if it was here i would of seen it in a google search but i was wrong sorry about that. But after looking at that schematic it shows the ALTERA EP3C40Q240 which i believe is in the anan 10 not the 10e. although it may be the same size...
by nubbyless
Sat Sep 05, 2020 2:25 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Anan 10e fpga heatsink size
Replies: 3
Views: 366

Anan 10e fpga heatsink size

Hi does any one know of a schematic for the 10e so I can look up the exact fpga size I know it's a EP3C25 but there seems to be several packages I would like to add a stick on heatsink to it. I have seen some pictures where people have done this maybe someone knows what size I should purchase. Thank...
by nubbyless
Wed Sep 02, 2020 9:54 pm
Forum: PureSignal Operations (PowerSDR & Thetis)
Topic: Is it ok to run pure signal at 384k with Anan 10E ?
Replies: 2
Views: 697

Re: Is it ok to run pure signal at 384k with Anan 10E ?

ok thanks ill test it for a while and see how it goes
by nubbyless
Wed Sep 02, 2020 9:09 pm
Forum: PureSignal Operations (PowerSDR & Thetis)
Topic: Is it ok to run pure signal at 384k with Anan 10E ?
Replies: 2
Views: 697

Is it ok to run pure signal at 384k with Anan 10E ?

Hi i have my Anan 10E and blf188xr mosfet amplifier up and running with pure signal using the xtronic sampler and the tr-plus tapr board. It seems to be working well i am only running at 192khz i thought i read somewhere that was as high as you can run with pure signal. Can i run it at 384k it seems...
by nubbyless
Sat Aug 29, 2020 4:23 am
Forum: SDR Console
Topic: anan 10E rear line in for microphone
Replies: 2
Views: 669

Re: anan 10E rear line in for microphone

Thanks I tried that before posting but it didn't seem to work
by nubbyless
Wed Aug 26, 2020 5:27 pm
Forum: Protocol 2 Firmware (all radios)
Topic: New -10/-100 16-BIT Hermes Protocol 2 Firmware Topic
Replies: 111
Views: 22838

Re: New -10/-100 16-BIT Hermes Protocol 2 Firmware Topic

Hi not trying to hijack your thread but curious how to modify k19 for pure signal can I just seperate the via trace to ground then feed in sample through Rx port? I tried the 50ohm resistor in series with Rx port and my xtronic sampler does not send enough signal to use it this way and I would rathe...
by nubbyless
Fri Jul 24, 2020 2:30 pm
Forum: SDR Console
Topic: anan 10E rear line in for microphone
Replies: 2
Views: 669

anan 10E rear line in for microphone

Is there a way in sdrc v3 to set the rear line in as the microphone I have selected microphone on radio but I believe this only uses the front mic input

Thanks
Fred w4yny

Go to advanced search