I have never been able to get the XLR 1/4" connector to work. I use mix 31 and have a good ground. I have tried running a ground to the shield of the connector and that didn't make it work either. I have used a Neumann 103 with a tube preamp and also a MXL BCD-1 direct to the XLR jack with the ...

Got the knobs working. I found the setup and had to put the radio IP in the box. Works great.
Tnx, 73 Jim K6JR

Got your software down loaded and the receive audio sounds great. I have the G2 with the display and knobs. The knobs are not working so I am using the sliders with my mouse. Is there a setting I need to change to make the knobs work?
Thanks for all you work.
73. Jim K6JR

Good Job!! Really cleaned up the receive audio on my G2. I have the G2 with the display and knobs. Is there a setup to make it work with the knobs on the radio? Right now I am just using the sliders.
Tnx, Jim K6JR

How do I delete the p2app file? Do I just move the p2app on the desktop to the trash?
Tnx, Jim K6JR

Hello Tony. Yep, 48 is better but still not good. There are at least 5 of us with the G2 display that are all having the same problem.
73, JR

Thanks Bob. I also upgraded the Pi and P2 and it is still not right. Tony says they are working on it but it has been a while since anything has been said as to whether or not they are making progress.
73, Jim K6JR

Well it has been 2 months that I have had the G2 with display and bad receive audio. Support, Tony and Doug are aware of the problem but I have heard nothing in regards to fixing it. The sounds of crickets on here also. I'm about to ask for a refund. I'll continue to use my other Anans that work cor...

I am using the slowest sample rate and only one receiver. Increasing the sample rate makes the choppy audio worse but lowering the sample does not get rid of the choppy audio just makes it a little better.

Laurence. thanks for the suggestion. I am 400 miles from home so can't try it now. Will get to it next week. The clicking / choppy audio has nothing to do with relays. It happens on the peaks of received audio.
Tnx, 73. Jim

Sorry. rec is received audio. I had contact with another g2 owner with knobs and he also has the choppy received audio when running piHpsdr. I bet they are all that way but haven't received any suggestions as to what to do about it. I have been in contact with Tony from support and Doug at the US re...

I have the G2 with knobs. The PiPHSDR rec audio Clicks and chops on peaks. The rec audio sounds fine on thetis. Tony said to upgrade the Pi and thetis which I did. There was no change in the choppy rec audio. The balanced tx audio works great now. I lowered the sample rate to 48000 and that helped b...

The lose wire was a braided ground wire outside of the radio going to the ground bolt on the back of the radio.

Thanks for the help. The problem turned out to be a lose ground at the back of the radio. It sounds great again.
73, Jim K6JR

Well thanks to both of you. I have never had RFI but i do have some clip on type 31s that I will give a try. The op amp is probably more sensitive to rf. My microphone is a Neumann TLM103MT with a 1 tube mic preamp/phantom voltage.

Since doing the software and firmware upgrades I have been using the TRS balanced input. The audio sounds great but I have been told that there is an echo/reverb effect. I noticed that when I switched to the TRS input the gain was very much higher than the regular mic inputs. I had to lower my mic g...

Thanks John. Mine worked with a new download of 2.10.0 but when I added some Profiles in memory and then shut the program down when it came back on the tx monitor would not work. Very strange.
73, JR K6JR

Hello Laurence.
Should the tx monitor audio be working on my G2 when using Thetis? I do not get any tx audio with the Mon button on and tx audio slider up.
Also does the G2 have a tx Monitor when in pi stand alone?

Tnx, Jim K6JR

I can not get any Monitor TX audio in Thetis. I have monitor on and the TX level turned up but no audio. I couldn't find a monitor position in the radio menu when operating it as a stand alone radio, no Thetis. What did I miss?
Tnx, Jim K6JR

Yep, I adjusted the monitor audio in tx and no audio. I was using thetis at the time.
JR

Got my G2 with knobs today. About 15 minutes later it was on the air. So far everything I have tried works except the tx monitor function. I don't get any monitor audio out on tx. Maybe a setting I haven't found yet. Anyone else have this issue? A nice looking radio except the Multi1 knob is not str...

FedEx has my radio and it has left the Melbourne Australia airport. Should arrive on my porch this Thursday. It is the G2 100 with knobs.
73, JR K6JR

Received my invoice for Saturn G2 with display. Order #4006. Date 3-27-2023

73, JR. K6JR

By the time anyone receives the 8000 DLE MKII it will be a year old design, There will be an extra one for someone else in the December group I just canceled my order. Apache Labs needs to get their act together. I waited 1 1/2 years for an Andromeda and canceled that order. Moving on.

Just received an email from Apache Labs. My 8000DLE MKII is delayed 6 weeks to the 3rd week of February. Due to the delay they are taking $200 off the price and paying to upgrade the shipping to expedited. That is the news for now.

I ordered a 7000 on August 6th, 2022 and it has been shipped by DHL to arrive on October 5th, 2022. 2 months, not bad. Shipped from India.
Thanks down under.

I have an excellent working Anan 8000DLE 200 watt LDMOS radio that I would be interested in trading for a 7000DLE MKII, the black one. I am looking for the smaller radio to travel with and I don't need 200 watts as I have a SPE 2k amp that only requires 36 watts of drive. If interested contact me at...

Jim N6ZN has a Blue Anan 7000 DLE in good working condition for $2000. You can reach him at his QRZ email address. He is in Lumis CA.

I found the same issue with PS but it also turns off the TX EQ. Confirmed on two different 7000s and two different computers.
Thanks for the great work.
Jim K6JR