Search found 11 matches

by LGPIGNOLET
Thu Oct 11, 2018 10:18 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: TX/RX relay switch times in CW mode
Replies: 1
Views: 1490

TX/RX relay switch times in CW mode

Can someone tell if when not in semi break in mode is the tx/rx relay supposed to switch at the speed of the keyer..? I was expecting the radio to key with no output until the key is pressed, not switch back and forth from tx to rx.. Is there a tx/rx delay setting somewhere, when not in semi break i...
by LGPIGNOLET
Fri Sep 28, 2018 12:07 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Rear connector panel tutorial
Replies: 5
Views: 1963

Re: Rear connector panel tutorial

Hi Scott,,,

So who designed the unit (email address) ? If I can't get the answer from the forum where should I go..?

Maybe i can contact the designers..?

tnx's
by LGPIGNOLET
Thu Sep 27, 2018 5:09 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Rear connector panel tutorial
Replies: 5
Views: 1963

Re: Rear connector panel tutorial

Hi Scott...

So where do I get clarification on specifically pages 15 &16 in the 7000DLE manual...?

If it ain't in the manual where do I go to get the answer...?

It's like there are pages missing in the manual..

Tnx's
by LGPIGNOLET
Wed Sep 26, 2018 8:14 pm
Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
Topic: Rear connector panel tutorial
Replies: 5
Views: 1963

Rear connector panel tutorial

Can someone point me to a tutorial for the rear panels connectors and their functions on the 7000DLE..

Tnx's

Larry
by LGPIGNOLET
Tue Sep 18, 2018 4:34 pm
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Re: Using VAC button in Power SDR

Hi Scott... I think the driver is working, but I agree I need to assign an input device .... That is the next step.... i'll let you know after I get that done... While I have you ,,, IS there a better more up to date manual available for the ANAN 7000 somewhere..? The one I have is dated Oct 2017...
by LGPIGNOLET
Tue Sep 18, 2018 1:33 pm
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Re: Using VAC button in Power SDR

Hi Scott,,

I did select the speakers and then I enable VAC button , but when I do that Power SDR generates a fault Invalid number of channels ...Try connecting a microphone to your computers sound card.. I then click Ok and get Invalid Stream pointer...
by LGPIGNOLET
Tue Sep 18, 2018 1:09 pm
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Re: Using VAC button in Power SDR

Hi Scott... After going through the configuration,,, I find that there is no recording devices in the list under the SOUND configuration tab in Win 7... but there are speakers under the play back tab... When I go to powersdr I see no input devices under the input tab , but I do see Microsoft Mapper ...
by LGPIGNOLET
Tue Sep 18, 2018 11:49 am
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Re: Using VAC button in Power SDR

Hi Scott...

So I read the tutorial, very good...
What I don't understand is..... If I want to route Power SDR audio to the speakers in the pc , let's say...

Q Is it still necessary to configure an input device such as a microphone in order to get vac to work...?
by LGPIGNOLET
Tue Sep 18, 2018 11:15 am
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Re: Using VAC button in Power SDR

Tnx's for the reply ,, but The tutorial you pointed me too does not load..?
by LGPIGNOLET
Tue Sep 18, 2018 12:51 am
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Re: Using VAC button in Power SDR

what version of os are you using...? WIn 7, Win10, etc tnxs

Not sure if I can reload Sound Mapper or where to get it..?
by LGPIGNOLET
Mon Sep 17, 2018 8:27 pm
Forum: PowerSDR mRX
Topic: Using VAC button in Power SDR
Replies: 12
Views: 2920

Using VAC button in Power SDR

Hi I'm told I can configure VAC buttons with HPSDR using MME as the driver and Microsoft audio MApper for the input and output .. Well The drop down for the output is Microsoft Mapper - OL , but there is nothing in the drop down for the INPUT..? Anyone familiar with Microsoft Mapper ..? or best way ...

Go to advanced search