Rob, You were correct in your assumptions. The problem was in the Windows 10 Pro (x64) Firewall! When I specified Thetis's latest version as a program allowed to pass the firewall and fixed all other possible Thetis rules to include Public and Private to pass, Thetis now works! The Failure problem h...

Rob, Thetis 2.8.11 does work with Protocol 1. Using the Windows Security interface, I only see the upper level rules. I noted that there is a rule for ALL on Thetis 2.8.8 and for Open HPSDR THetis 2.8.8 but none specifically for 2.8.11 There are rules for Thetis Public which is blocked and Thetis Pr...

I had been running Thetis at 380+K for several months successfully prior to the failure with Protocol 2 v2.1.18. I uninstalled Thetis, removed all its appdata information and reinstalled it. I had hoped that the problem was due to a corrupted table somewhere. Evidentally not. I will try to update Th...

I am running the 32 bit version of Thetis because I don't have the magic instruction required for running the X86 version of Thetis 2.8.11 (F). Because I have not patched a program, I chose to reload Protocol 1.5.4. It works with PowerSDR mrx and Thetis 2.8.11 (X86). Audio and Video produce the expe...

What was the original firmware that you had in there that worked? Metis_Orion_MkII_Protocol_2_v2.0b How do you get audio out of the radio? Speakers/headphones attached to the 8000, VAC, what? Direc from radio Have you tried reverting to a fresh database in Thetis? Yes. It does not help. SDR Console...

I had a working 8000DLE under Thetis 2.8.11 until I bootloaded Protocol_2_v2.1.18. After that I received no Signal video or audio with Thetis 2.8.11. I do receive video of the signal under SDRConsole V3.x. I tried going back to Protocol_2_v2.0b. It installed but still no audio. I tried a direct cabl...

Thanks to Doug and others who commented.
This is the reason it did not work.

73,
Ed, AI1R

Running Windows 10 Pro Insider version 19042.508, i.e.. 20H2. 2.8.8 x86 installs and runs well. Installing 2.8.8 - x64 completes the FFT table and before reaching the display, disappears without signalling an error visually. If I attempt to run the "partial installation" after rebooting, I...

With PowerSDRmx, I was able to use a straight key. With Thetis 3.4.8 (October), I can't seem to turn off the automatic keying.
I have turned off options that would control/enable paddles without success. Any help would be appreciated.
Thanks and 73,
Ed, N5EI

I am trying to determine the minimum and maximum levels at the PS input for satisfactory PS implementation. I have an Xtronic coupler and a linear amplifier for my 8000DLE. I am concerned that at 1500 W PEP the feedback level provided by the Xtronic XDC-4SO might be too high and that at 300 W PEP th...

Evidently the DB upgrade did not work correctly. When I reset the DB, the problems went away.

Using the 9/12 version I continually get AMP Overload whether an amp is connected or not on an 8000DLE using Protocol 1.9 and an upgraded 2.6.7 database in receive mode. If I adjust drive up from zero, the drive quickly decreases toward 0.

This is a big problem with transmitting on the 7000 and 8000. SDR-Console does not seem to expose the "gain coefficients" that PowerSDR-mRX and Thetis use to limit the maximum power to around 200 watts for the 8000 and 100 watts for the 7000 on each band. I am also wondering about PTT whic...