Hi, I would like to highlight a problem I had configuring SDC-Skimmer to make it work with Thetis. Everything is fine configuring SDC Control Type with " Audio + TCI ". Anyway I noticed a little frequency difference in the signals shown in SDC and the signals shown in Thetis panadapter. Wi...

I am sorry for not having read the "Thetis 2.9.0" main thread, I should have searched better. The important thing it is the correct behaviour. Actually I didn't said I installed the latest release (2.9.0.6 x64) because I was trying to fix a problem with TCI and SDC-Skimmer. Anyway I'll rea...

Hello, I am having a odd behaviour when I enable the Auto AGC-RX1 function. As you can see in the picture below, I have to set a very high value (26db) to keep the threshold few db over the noise floor level. I don't know what I am missing but it seems I have inadvertently set a 20db offset somewher...

Hi,

I am wondering how can be recorded the audio and the screen while using Thetis and CW Skimmer.
I can't find a way to feed the audio stream to Bandicam because VAC-1 is dedicated to the I/Q stream and VAC-2 is dedicated only to the RX-2.

Thank you in advance for any help

73' Enzo
iw7dmh

Hi, thank you very much for the further clarification. Considering I am planning to use a power amplifier a 30ms delay is not so bad. As Scott pointed out it is unavoidable and it happens on other rigs as well. The important things are not damaging the rig and be on air with a understandable code. B...

Hello, thank you very much for your answers. I have to confirm what Gary said: i have no issue in SSB mode using the mic PTT or the MOX Thetis button. The problem is only in CW mode and as suggested, after having set Key Up and Key Down both to 30mS, it was solved. Now, it is still not clear for me ...

Hi, I connected a RX terminated loop on my 7000-DLE ANT-2 connector. I am planning to use it on 20/30/40/80/160m so I configured the Antenna control as in the picture below. ANT-Control.jpg Ant-1 should be the only transmitting antenna. The problem is that, each time I start transmitting, Thetis (2....

w-u-2-o wrote:Change the TX Grid Scale to max 15, min -17, step as desired.

Change the waterfall low level to -70, and the high level to -20.

Any energy below -70 is simply a "don't care", no one will ever see it or hear it.

Thank you very much dr Scott,
now it is far better.

73' Enzo
iw7dmh

Hello, I would like to view the transmitted signal in the panadapter, mostly when I am working in split. I enabled the DUP and MultiRX functions but the signal shown is actually huge, about 60 KHz, as you can see in the picture below. I am wondering if i am missing some config parameter or there is ...

Thank you Scott,

unfortunately I don't think I can fix or program a new firmware.
I was just playing with the discovery protocol and noted the issue I described before.

73'

Hello, I am observing a odd behavior looking at the network connection of my Anan 7000 DLE (blue). The rig is loaded with the UPDATE 2.0b 10 Feb 2020 firmware and I set up a fixed IP ( 192.168.0.14 ). Having it a fixed IP Address I expect that a ping -t 192.168.0.14 command constantly returns a vali...

Hi, it seems that it is more than a plan. A headless RPI next to any Anan rig would implement the client/server model you talked about before. It is also the same design used in ExpertSDR Remote System. I hope it will be released asap (y) Best 73' Enzo, iw7dmh https://www.youtube.com/watch?v=UEgcAgh...

Thank you very much.
It works fine (y)

73'

Hi, another dumb question: is it correct I can't have a permant storage of the Audio-VAC1 settings? Each time I restart Thetis I have to check the following three flags: - Stereo - Combine VAC Input Channels - Direct I/Q - Combine VAC Input Channels Also, what is the general rule in running Thetis? ...

Hello Mike,

thank you very much for your hints.
It works very well now.

Best 73'
Enzo

Hi, I am having some problems making Thetis 2.8.11 and CW-Skimmer 2.1 working together. I followed the guidelines by Rafael, NN3RP, that I found in a previous tread https://apache-labs.com/community/viewtopic.php?f=9&t=3273&p=11252 : CW-Skimmer can read Thetis frequency (via Omnirig-TS2000) ...

Hello Erik,

I appreciate a lot your clarifications.
I am new to the Apache Labs world and there are a lot of things that aren't very clear for me.
Anyway community is a great starting point

Thank you very much
73' Enzo
iw7dmh

Hi,

this was not my initial question, anyway I am more familiar with PC software and I find Thetis interface a bit odd and sometimes difficult to use.
PiHPSDR is very nice and meets all recent usability requirements.
Using a smart console and a PC could be a good solution, mostly during a contest.

Hello, I have some questions about the V2 Controller. I am wondering if the overall RX performance is the same as Thetis client. Apart from the reduced samplerate, I suppose the RX performance is the same probably because the WDSP lib is the same in both programs, but I am not sure. Also I am wonder...

Hello Scott,

thank you for the clarification. I had just seen the minimum samplerate I can set up in Thetis (48KHz).
I am sorry for having asked the question in the wrong section of the Community.
Maybe you can move the whole discussion in the right place.

Best 73'
Enzo, iw7dmh

Hi Gary, still don't but I will. I am collecting infos from some time now because, unfortunately in my region nobody own an Anan rig. Anyway 10.6 Mbps for 1 RX is too much for my remote shack (through private VPN). Maybe I can set the samplerate at 39-KHz - I have to read in depth in the Thetis manu...

Hello, I would like to know the typical network bandwidth usage of a 7000DLE and which are the Thetis parameters to be set for increasing or decreasing it. One should be the samplerate but maybe there are some others. I am thinking about something like the panadapter width and/or the waterfall speed...

Thank you very much dear Hans,

I didn't aware of the DE shop.
I'll contact him.

Merry Holydays and best '73
Enzo, iw7dmh

Thank you Scott and Hans for your help. Maybe you already are aware of a very explanatory doc in the TAPR Openhpsdr repository https://github.com/TAPR/OpenHPSDR-Firmware/blob/master/Protocol%202/Documentation/openHPSDR%20Ethernet%20Protocol%20v3.8.pdf In the ending part of the document I found a in ...

Hello, I'm resuming this old message because I would like to know the differences between the 7000 DLE blue version and the 7000 DLE MKII black version. Maybe the question is already answered somewhere, but I didn't find it on the forum. I would like to buy the new black MKII, but I may have opportu...

Hello Scott,
thank you very much for the hints and for pointing me up to the WDSP doc.

73' Enzo
iw7dmh

Hello,

I am wondering if the Thetis AGC Gain control has the same behaviour as the AGC-T control described in the Flexradio Document (https://www.flexradio.com/documentation ... -controls/).

Thank you very much and 73'
Enzo, iw7dmh

Ok Laurence this make sense. Looking at the initial picture I was assuming the interface would be simplified. Does it means the controls in Andromeda forms can have the same skin like the ones in the main interface? For example like the RUN buttons; MON, TUN and so on. (sorry for my bad English) 73'

Thank you Laurence and thank you Rob. I'll try to go more in depth with the code. I would like to understand how the GUI event listeners are invoked and how the GUI sends commands to the underline WDSP engine. I already found the Thread system that updates the GUI but inspecting a class with more th...

Hi Bob, thank you very much for your hint. It is actually what I had in mind. I read about the Thetis skin features on your web site and I am wondering if the new Andromeda GUI controls will be "skinnable" as well. Also, I can't find any download for the 2.7.0 release. Can you give me any ...