I do the instalation with the .msi installer and it stop starting when message 'initialiazing portaudio' aperar. I have W10 here. I do a reinstall, install again and always fail at the same point. Old thetis 2.7.0 ( a2) work fine.
I miss a lot when working in the contest ( not finised yet ) colapse thetis in the upper side of screen and working the second virtual receiver 'in band' , but.... i loss the VFO B read, o only can watch the colour and the line if in split. There is a lot of space available for another VFO box with ...
I use firmware 11.6 and angelia board in Anan 100D. Is it possible to do cw via some pin of the aux connector ? I read in the firmware notes that IO5 is a external CW keying. Textual: "added IO5 external CW keying feature for ext amp autotune support in iambic CW mode, using debounced IO5, chan...
Last week i solve a problem in my 100D. It was the SMA 90 degrees connector in the Angelia board. It is in a forced position with the cable from the RF board. The connector seem good at a eye inspection but it fail in RX time to time. I solder the body of the connector with a heavy iron and from tha...
I do a fresh install of 2.6.8, the lattest ( 11/3/19). My hardware is anan 100D and firmware 11.6. I tested all Richie versions and working fine prior to this release. With this version when I start the radio from a reset database, and prior to change parameters in setup ( radio audio etc ) it work ...
Hi all, here I have anan 100D also the first edition, grey box. Firmware is 11.6 and the very last Thetis. Time to time the RX seem to be deaf, all signals go down and under the noise line level in the panadapter window ( under the scale ). If i transmit in cw some dits sometimes cure the problem an...
Hi all again. I use a lot my Anan 100D in remote and my mode 99% is CW. To use a real keyer in remote I have a modified K3NG that send via serial port ASCII and i use a virtual port to link to the remote pc, here another virtual port send the ascii to a winkeyer ( k3ng via a serial port ) and that m...
Hi, when you enable 'MultiRX' the second virtual receiver VFO B window don't follow the filter and mode as the VFO A. It follow filters and mode in the audio and in the panadapter but the info in the VFO B window not, it is unchanged.
When Spotting is enabled and in cw mode the line with the callsign is shifted by the side tone frequency. Is it possible to put the line just where the panadaptor show a signal ?
Hi, very impresive all the work Richie. To check the files you upload to dropbox is there any trick?. My tentatives to install it always get some error and I can't test the versions. I use the oficial 2.6.8 ( 9/10/19). I use a old machine that usually are at 50% load with the basic radio programs, i...
Fine ! at the first attemp i solve the problem. Downgrade the firmware to 11.9 and all work as expected. Now I note the audio a bit 'crispy' connected at the jack front pannel, not VAC.
The combination here is Thetis 2.6.7 and 11.9 in firmware.
Hi, yesterday I do the upgrade to protocol 2 after long time using my Anan 100D. I note that with Thetis and SDR console the selection of antena fail, The relay don't switch and the receiver is connected to Bypas input. If i connect antena to RX2 receiver all if fine. In I connect the antena to port...
What setup can enable my ADC2 using RX2 bnc to monitor a second band while i transmit ? In a contest, for example, transmit in band A and continue receiving in band B to search for multipliers. I have Anan 100D and not sure about the version of the RF board.
Hi, can somebody , please, say me the 'normal' current draw by a Anan 100D in 6m band for 100W output ? I am alarmed by what I see in the power supply current meter. A 320W power supply cut by excesive current. In HF bands 20A is normal in all bands, now in the sporadic season I start operating in 6...