Search found 23 matches
- Thu Feb 15, 2018 5:19 pm
- Forum: Remote Operation Over The Internet
- Topic: Anan 10-E remote operation.
- Replies: 80
- Views: 179549
Re: Anan 10-E remote operation.
Hi Scott, Is there a detailed description available to do Hpsdr remote operation using team viewer ? I installed it and started trying. I get audio in my ipad, when I play a youtube audio. But not get SDR audio in ipad. I have VMB in my PC. Can anyone who has tried it to help me further ? Rds Prem, ...
- Mon Feb 12, 2018 3:35 pm
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13526
Re: Homebrewed PiHpsdr
Hi All, I have completed my PiHPSDR project and Rx part work ok. During Tx, the meter needle stand still in Tune and even in MOX mode, @ 41W.I can see voice peaks in display screen, while talking to mic. Also the SWR and ALC reading (below S meter needle) digits changes. My Radio is Hermes followed ...
- Tue Feb 06, 2018 2:11 pm
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13526
Re: Homebrewed PiHpsdr
Hi John, I could not understand your advise for some test. Can you expand further please. In RPi Rasbian screen on monitor, usually we get some buttons to start programs and to explore RPi features etc with Icon Pic as Rassberry fruit" After some wrong fiddling by me these buttons are not visib...
- Tue Feb 06, 2018 12:53 pm
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13526
Re: Homebrewed PiHpsdr
Hi Team, I have homebrewed my RPi controller for me HB Hermes. I notice that the HPSDR shutdown after few minutes of running. Even the HPSDR screen disappear ! What could be wrong ? I run web browser and watch YouTube video without any issue. I power my Pi from a 5V , 2A rated power adaptor. I use ...
- Tue Feb 06, 2018 12:52 pm
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13526
Re: Homebrewed PiHpsdr
[quote="Prem"]Hi Team, After spending some time with my PiHPSDR, I came to notice that once I store a freq and later if I recall this freq stored from MEM menu, this PSDR vanishing error happens. Is anyone else noticed this or else an issue locally in my unit ?. Please share your thoughts....
- Tue Feb 06, 2018 8:12 am
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13526
Re: Homebrewed PiHpsdr
Hi Team, I have home brewed my RPi controller for me HB Hermes. I notice that the HPSDR shutdown after one or two minutes of running. Even the HPSDR screen disappear ! What could be wrong ? I run web browser and watch YouTube video without any issue. I powered Pi from my Phone power supply, 5V , 0....
- Sun Jan 28, 2018 5:02 pm
- Forum: PowerSDR mRX
- Topic: FlDigi Configuration with PSDR
- Replies: 5
- Views: 6011
Re: FlDigi Configuration with PSDR
Dear Mike, Scott
Auto option already unchecked here !
In DIG mode, the CW decoding is not happening well. S I need to try some other option.
Since my CW capability is very litle, I need to have software support . hi
73s
Prem
Auto option already unchecked here !
In DIG mode, the CW decoding is not happening well. S I need to try some other option.
Since my CW capability is very litle, I need to have software support . hi
73s
Prem
- Sun Jan 28, 2018 8:35 am
- Forum: PowerSDR mRX
- Topic: FlDigi Configuration with PSDR
- Replies: 5
- Views: 6011
Re: FlDigi Configuration with PSDR
Hi All,
I notice that if I select DIGL/U in SDR screen, I get power out.
Is that the correct way ??
If I select CWL/U, power out is zero.
73s,
Prem
I notice that if I select DIGL/U in SDR screen, I get power out.
Is that the correct way ??
If I select CWL/U, power out is zero.
73s,
Prem
- Sun Jan 28, 2018 7:07 am
- Forum: PowerSDR mRX
- Topic: FlDigi Configuration with PSDR
- Replies: 5
- Views: 6011
FlDigi Configuration with PSDR
Hi Team, Can anyone help me to set up Fldigi for running CW with my Hermes and PSDR ?? I tried, using Hamlib for Rig control in Fldigi, using one Com Port from PSDR (Com 14) . Com 24 in PSDR paired with Com-14 using Com-0-Com. When I press Tune or T/R in Fldidgi, I get CW side tone from speaker, Rad...
- Wed Jan 24, 2018 5:34 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Scott,
So we have to connect external audio between Left/Right Pin and Ground ??
Ground will be our common line for L&R Line In ??
73s
Prem
So we have to connect external audio between Left/Right Pin and Ground ??
Ground will be our common line for L&R Line In ??
73s
Prem
- Mon Jan 15, 2018 5:53 am
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Scott, Good Day to You. So I will take either line out or speaker out from Radio to PC , so that I can get side tone thru VMB and PC audio out. Can you suggest me the external audio rack connection to Hermes accessory pins ?? As per schematic we have two Pins marked as Left and Right. Since out e...
- Mon Jan 15, 2018 2:06 am
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Gary,
I keep my radio little away from my seat and monitor. So if I get usage of VAC audio was useful. Else I have to wire Radio audio to PC line in and use with VAC.
Request others who are using VAC and CW , share their experience.
73s
Prem
I keep my radio little away from my seat and monitor. So if I get usage of VAC audio was useful. Else I have to wire Radio audio to PC line in and use with VAC.
Request others who are using VAC and CW , share their experience.
73s
Prem
- Sun Jan 14, 2018 3:26 am
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Gary,
I had noticed open connection on U9-76 Pin.
How I can eliminate TX going to Off between words, while I sent CW ?? The PTT relay clicking between words is annoying. There will be some setting to avoid this ?? Please advise me.
73s
Rds,
Prem
I had noticed open connection on U9-76 Pin.
How I can eliminate TX going to Off between words, while I sent CW ?? The PTT relay clicking between words is annoying. There will be some setting to avoid this ?? Please advise me.
73s
Rds,
Prem
- Sat Jan 13, 2018 12:31 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Friends, After a detailed troubleshooting opening the box on my Hermes board, I could notice that one CW line pin on U9 had a dry soldering and which was the trouble for my CW faulty MOX . I corrected dry soldering and now , only if I short either Key point to ground only it switch to MOX. I am n...
- Fri Jan 12, 2018 10:37 am
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Stu, I had refreshed the Firmware more than one time during earlier testing. I tried connecting (shorting Key points or Pins), no change visible in screen. I did not open to check the voltage. Will do that. can you let me know the real working during CW mode ? Will the Radio go to TX (MOX ON) mod...
- Thu Jan 11, 2018 3:41 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Scott & Gary, I refered back to my schematic dwg print which I was using during my Hermes aseembly and testing. There I have recorded the voltages at U25 Pins : 3,4 which are Dot and Dash key in points . Also Pins : 16 & 17 which are out from U25 . These out pins go to FPGA Pins. I had 3....
- Thu Jan 11, 2018 8:45 am
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Gary and Scott, Before opening my Hermes box for voltage test, I made one more short video to show you what happens if I switch off Lambic keyer option. The meter swing stops now. Earlier in my DSP- CW - Connections : Both were none. I changed first one to Radio, as you advised. Video was taken a...
- Wed Jan 10, 2018 5:28 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Gary,
Some of the points in your procedure was confusing to me and I have done as I could understand. Please have a look at the video prepared to see how my Hermes behave with CW mode.
Please help me further.
http://www.youtube.com/watch?v=INP6dfVNSbk
Rds,
Prem
Some of the points in your procedure was confusing to me and I have done as I could understand. Please have a look at the video prepared to see how my Hermes behave with CW mode.
Please help me further.
http://www.youtube.com/watch?v=INP6dfVNSbk
Rds,
Prem
- Tue Jan 09, 2018 6:01 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Scott, Gary Thanks for reply. As Gary mentioned, I don't get a continuous DOT or DASH !! So it can be something else than a short to ground. Is it ? Please see the screen shot when I select CW mode. It switch to "MOX" not "TUNE". But . still I get same output power as if TUNE ...
- Tue Jan 09, 2018 5:48 pm
- Forum: PowerSDR mRX
- Topic: PowerSDR mRX Transmit Audio Setup
- Replies: 9
- Views: 43034
Re: PowerSDR mRX Transmit Audio Setup
Hi Scott, Thanks for reply. All my audio devices set for 44100. Is this ok or any issue. 44100 setting was used to ensure all Digital mode software also run well. I have read somewhere as 48000 setting may not work with some software. Not sure! Is the MON audio from PSDR is reliable reproduction and...
- Tue Jan 09, 2018 5:40 am
- Forum: PowerSDR mRX
- Topic: PowerSDR mRX Transmit Audio Setup
- Replies: 9
- Views: 43034
Re: PowerSDR mRX Transmit Audio Setup
Hi Team, I started working regularly on air with my HB Hermes, after a lot of issues and rectification with the help of my "expert" friends like Scott. Martin, Kjell, Phil, John, Mike and some others. Now I need to fine tune my audio profiles for SSB. I have B1 Mic and UMC22 USB interface ...
- Sun Dec 24, 2017 12:43 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
Re: CW Mode Operation
Hi Scott, Yes, it is on my HB Hermes. Any suggestion to find faulty point ? Without key, what shall be the signal at U25 Dot and Dash Pins ?? At low or hi ?? Do you expect a short from Dash to ground ? In that case, we need to get continuous Dash !! I get my TX in MOX mode without any break in signa...
- Sun Dec 24, 2017 6:57 am
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39395
CW Mode Operation
Hi Team,
I have been facing a trouble while using my Hermes board. When I select CW mode, the Radio switch immediately to TX mode, as if we pressed MOX button. I have not connected any key to radio !
Please advise me if it is any setting issue here ?/
73s
Prem
I have been facing a trouble while using my Hermes board. When I select CW mode, the Radio switch immediately to TX mode, as if we pressed MOX button. I have not connected any key to radio !
Please advise me if it is any setting issue here ?/
73s
Prem