The stream has to be cut into separate presentations - this will take place soon. It looks then like: Unbenannt.JPG And by searching around in the net i found a Thetis User-Manual as PDF from G8NJJ :: http://www.nicklebyhouse.co.uk/index.php/downloads/category/13-sdr?download=55:thetis-manual-draft-...

Andromeda was presented by Kjell Karlsen LA2NI on the Ham-Radio-Online 2020 Youtube-Stream - which was only online during the 28. June - but as I heard - the stream will be cut into the different presentations and shoud be online in ? one to three weeks ? on the SDR-Academy-Channel: https://www.you...

Hi Tom, it´s not so easy to have all settings right for qsk - I will give it a try here with my pictures - hope that are all needed for. Steps if you are starting Thetis 2.7.0 a3 with QSK Delay 0ms (this is also in setup - DSP - CW) The AGC is in custo and the settings in setup - DSP - AGC (see slop...

The AGC settings are not set as they shoud be for QSK after starting Thetis 2.7.0 a3: work around: after starting Thetis switch the AGC once to fast - and then back to custom then you will have full short recovery of the receiver in QSK Sri that we have no support at the moment from Rick and other d...

Hallo Hans, I have the CW Keyer and use only the key output - ptt is only needed, if you will use it with other programs for a ptt-port in usb devicerouter. The key-output of the keyer has to go on your anan (no photo of the black one - only blue one) to the dig in2 as you did and without ptt it sho...

One step further today: in Thetis VAC1 MME and not WDM/KS with VACable 4.60 (my payed version) in CWSkimmer MME and not WDM/KS Only vy strong stations have a bit artifacts, but the dynamik-range of the IQ-stream is much better. The straight-line is still visible. I have Omnirig TS-2000 running, freq...

This ist the answer to Virtual Audio Cable : Hello, Helmut, > We found, that with VACable Version 4.15 the Datastream to the CWSkimmer > (CW-Decoder Program) is clear and undistorted, > with my 4.60 and also tested 4.62 Trial there are heavy artifacts on the > CWSkimmer Waterfall. Since I'm not fam...

Rafael,

I did write to the support of VACable and will report if I get answer.
Attached him the link for this thread.

73 Helmut

Hi Rafael and Scott, Rafael, you use Version 4.15 of Virtual Audio Cable, and that makes the difference. I searched today for 4.15 but could only find 4.14 on the web. Installed the 4.14 and the CW lines where clean as yours with 4.15, but abt all 20seconds was an short interruption - so 4.14 is not...

Hi Rafael,

thank you for your kind help. I see you have the PC-Version of the MK2 - I have it without but the same solid case.

Nex I will check the Ethernet connection between my I7-PC - and the MK2. May be there is the stream problem.

Will report here next week.

Best 73
Helmut

Hi Rafael, yes that looks how it should be - clear Skimmer without artifacts :) Now let´s try to find my problem with comparing versions: my setup is on a 7000dleMk2 Windows 10/64 pro 1909 with last updates, PC is I7-6700K with Intel Grafics 530 (included in Prozessor) no separate Grafic card Thetis...

Rafael, when I check your screenshots in this thread, the strongest station has also some gritty (dont know the correct word in english) around and making wrong decodes but this is not so strong artifacts than on my screen or also on SM7SJR tutorial. Would like to see another screenshot of Skimmer w...

Rafael, I had in my first posting with the picture of my setup: I was testing CWSkimmer 2.1 with my 7000dleMK2 / Thetis 2.7.0 a3 / Firmware Protocol_2_v2.0b.rbf with the Virtual Audio Cable from E. Muzychenko Version 4.60 and Win10/64 prof. Simon, the writer of SDR-Console posted a setup and has not...

Hello Om´s, I think I found the reason, why there are so much artifacts - on Simon´s SDR-Console Site: The spectrum and Waterfall in SDR Console use DirectX graphics, CW Skimmer uses GDI / GDI+. It is possible that the two do not behave together well causing the SDR Console waterfall to stagger. Som...

Thank you Rafael and Scott,

I will try it again tomorrow with the volume sliders in win10 and Thetis.

SM7SJR has a tutorial from Feb. 2020 for an Anan 200D - will compare it and use the 96000 sampe rate.

Best 73
Helmut

Thank you, Rafael When I was testing the setup with the turorial, I could not find - how to reduce the level of the IQ-stream. In Win10/64 the SOUND setup, where you can change the sampling-rate and the level - there was no reaction to see on the Skimmer waterfall. Do you see a way to change this le...

I was testing CWSkimmer 2.1 with my 7000dleMK2 / Thetis 2.7.0 a3 / Firmware Protocol_2_v2.0b.rbf with the Virtual Audio Cable from E. Muzychenko Version 4.60 and the Skimmer looks like the picture I found on SM7SJR tutorial - so there are awful artifacts with every decoded stream. I saw on the Flex ...

I had both cases for the 7000dle and 7000dleMK2, and I would ever prefere this one I have here: https://apache-labs.com/community/download/file.php?mode=view&id=1161 https://apache-labs.com/community/download/file.php?mode=view&id=1160 https://apache-labs.com/community/download/file.php?mode...

The cable is not so important, you need something like this: https://www.palmer-germany.com/en/products/di-boxes/5109/di-reverse You could make it yourself with an 1:1 Audio-Transformer ! Another link: https://apache-labs.com/community/viewtopic.php?f=12&t=2790&p=5387 ... With balanced mikes...

Hello Richie, tnx for the 2.7.0 a3 Version, running here on my 7000dleMkII with Firmware Orion_MkII_Protocol_2_v2.0_pre8. I was testing setups with all modes and found only one fault in FM-mode when leaving Thetis with RX1 and RX2 SQUELCH set to a value (50 here) the Values are not stored and after ...

RE CW: 7000dle mk2 / Firmw. pre8 / Thetis 2.6.9-C3 with three mode QSK button GUI: when on QSK and closing thetis, after starting again there is SEMI on the button. the QSK delay value is not stored when closing thetis Firmware: when starting thetis and setting QSK the AGC Custo is not set, it has t...

Request.... Is it possible to have a vertical gain adjustment included within the "Scope" and "Scope2" feature on the main gui ? Also , does anyone have a clue how to get the playback feature working when in VAC ? tnx garyradio / wa1oxt See my post on page 12 of this thread how ...

When using -playback- with my ASIO Interface I have to check the box in SETUP-AUDIO: I use MOX to override/bypass VAC for phone (PTT ans Space works similar) after recording have to press first MOX - then PLAY for playback and ending the playback press first PLAY - then MOX the output of the playbac...

Hi Scott, no under and overflows when VAC Force is disabled - the waterfall looks like normal, but the audio is pigtail hihi.... 73 Helmut When Force is enabled I can run for hours in FT8 without any flaws and flows.... https://up.picr.de/37277408sf.jpg Sorry, Scott, was to fast ..... so let´s wait ...

Hello Nigel, this is similar to what I posted some time ago, https://up.picr.de/35721818fa.jpg I have set now both VAC to Force. It is here Vac2 but same settings for Vac1 when doing FT8 etc. https://up.picr.de/37275960pu.jpg So I see that it is not only with the VoicemeterBanana Drivers that I use,...

Thank you Richie for E2 - running vy well here... and the Video with moving panafalls....amazing !

I think Doug has missed the -CATStructs.xml- file in the -Thetis_2.6.8_3Nov19_e2.7z-

Did not try the .msi...

73 Helmut

You click it so it turns blue, to give it focus, you can see the 'caret' flashing on the right hand side. This is so you can type numbers in there, as a 'normal' text box. Mouse wheel does not work when blue, at least i haven't ever seen it working like that. To use mouse wheel you just hover the m...

Hi all, for your info - with the D6 version scrolling the qrg with the mousewheel won´t work in the panadapter when I before tried to scroll in the frequency window. Have now 4.1d and all o.k. 73, Helmut Which d6 version? and where are you using the mouse wheel? If you are just using mouse wheel in...

Hi all,

for your info - with the D6 version scrolling the qrg with the mousewheel won´t work in the panadapter
when I before tried to scroll in the frequency window. Have now 4.1d and all o.k.

73, Helmut

Gary, I think it is not a noticable difference - if you compare the results of Rob Sherwoods PDF at nc0b.com/imd you can notice, that the IMDs are between 20 and 37 dBc on both the PowerGenius XL and the KPA1500. Most visible is the huge variation from band to band. I see also the variation of the c...