Search found 76 matches
- Tue Feb 06, 2018 9:20 am
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13527
Re: Homebrewed PiHpsdr
Hi Team, After spending some time with my PiHPSDR, I came to notice that once I store a freq and later if I recall this freq stored from MEM menu, this PSDR vanishing error happens. Is anyone else noticed this or else an issue locally in my unit ?. Please share your thoughts. Also can you help me to...
- Tue Feb 06, 2018 7:11 am
- Forum: piHPSDR
- Topic: Homebrewed PiHpsdr
- Replies: 10
- Views: 13527
Homebrewed PiHpsdr
Hi Team, I have homebrewed my RPi controller for me HB Hermes. I notice that the HPSDR shutdown after few minutes of running. Even the HPSDR screen disappear ! What could be wrong ? I run web browser and watch YouTube video without any issue. I power my Pi from a 5V , 2A rated power adaptor. I use m...
- Sun Jan 14, 2018 5:04 pm
- Forum: PowerSDR mRX
- Topic: CW Mode Operation
- Replies: 34
- Views: 39414
Re: CW Mode Operation
Hi Gary, After increasing delay to 360 ms, I could get rid of that issue. One more thing to get clarified . I use VAC and listen to radio RX as well as MON signal thru VAC and so PC audio. But in CW mode , I think we get CW TX side tone only thru head phone jack on radio ? What is function of “Semi ...
- Thu Dec 14, 2017 5:16 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Thanks Ervin and Scott for guidance given.
My Touch OSC Layout in my iPad is working ok now.
73s
Prem
My Touch OSC Layout in my iPad is working ok now.
73s
Prem
- Sun Dec 10, 2017 1:27 pm
- Forum: PowerSDR mRX
- Topic: CW MODE ERROR
- Replies: 0
- Views: 2463
CW MODE ERROR
Hi Team,
I notice that in my Hermes PSDR, when I select CWL or CWU mode, immediately radio move to TX mode!
Is this a hardware fault or any software bug ?
I have disabled MIC as well as VAC. Still same issue.
Can someone advise me on this issue ?
73s
Prem
I notice that in my Hermes PSDR, when I select CWL or CWU mode, immediately radio move to TX mode!
Is this a hardware fault or any software bug ?
I have disabled MIC as well as VAC. Still same issue.
Can someone advise me on this issue ?
73s
Prem
- Sun Dec 10, 2017 7:55 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi,
My doubt is that, if the RX1 Vol is same as VFO A Vol ??
73s
Prem
My doubt is that, if the RX1 Vol is same as VFO A Vol ??
73s
Prem
- Thu Dec 07, 2017 5:39 am
- Forum: Protocol 2 Firmware (all radios)
- Topic: Hermes Protocol 2 firmware v10.3 released
- Replies: 47
- Views: 79609
Re: Hermes Protocol 2 firmware v10.3 released
Hi Scott, Where we need to limit FPGA Temp ? Now my FPGA with Pro-1 running , max temp on heat sink is 39 Deg C, with my room temperature at around 9 deg less always. I have a heat sink fixed to FPGA and then I have a small fan on box top which blow air to FPGA heat sink. Can I directly load Pro-2 f...
- Wed Dec 06, 2017 6:10 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Erwin,
Thanks for response.
I have noticed VFO A & B Vol. Is it same as RX1 & RX2 Vol or AF ?? If same, why we have two different functions ?? That was confusing me.
Even in PSDR screen, we have
AF
RX1 AF
RX2 AF
Then separate vertical Sliders named as " Vol"
73s
Prem
Thanks for response.
I have noticed VFO A & B Vol. Is it same as RX1 & RX2 Vol or AF ?? If same, why we have two different functions ?? That was confusing me.
Even in PSDR screen, we have
AF
RX1 AF
RX2 AF
Then separate vertical Sliders named as " Vol"
73s
Prem
- Wed Dec 06, 2017 2:57 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: Hermes Protocol 2 firmware v10.3 released
- Replies: 47
- Views: 79609
Re: Hermes Protocol 2 firmware v10.3 released
Hi Scott,
Do we need to do any modification than changing fuse , to load Protocol 2 software to Hermes ? I feed 13.8V to my Hermes and 5V and 12V are onboard generated.
Rds,,
Prem
Do we need to do any modification than changing fuse , to load Protocol 2 software to Hermes ? I feed 13.8V to my Hermes and 5V and 12V are onboard generated.
Rds,,
Prem
- Tue Dec 05, 2017 4:20 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
I could see
Vol VFO A &B
AF Gain which is Master AF in PSDR screen
RX2 Vol.
RX1 AF or Vol not seen
Also CTUNE not seen.
Can you tell me the Text seen in Mapping list for these missing functions (in my case) ?
73s
Prem
I could see
Vol VFO A &B
AF Gain which is Master AF in PSDR screen
RX2 Vol.
RX1 AF or Vol not seen
Also CTUNE not seen.
Can you tell me the Text seen in Mapping list for these missing functions (in my case) ?
73s
Prem
- Tue Dec 05, 2017 2:08 pm
- Forum: Protocol 2 Firmware (all radios)
- Topic: Hermes Protocol 2 firmware v10.3 released
- Replies: 47
- Views: 79609
Re: Hermes Protocol 2 firmware v10.3 released
Hi Team,
I wish to have a try on Protocol 2 firmware on my HB Hermes. Any risk ? Any special care needed ?
What are the main advantages with this PC -2 ??
73s
Prem
I wish to have a try on Protocol 2 firmware on my HB Hermes. Any risk ? Any special care needed ?
What are the main advantages with this PC -2 ??
73s
Prem
- Tue Dec 05, 2017 2:01 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
Thanks for compliment.
We miss the Freq read out when away from PC screen ! We should be able to see the freq ! Rest all OK .
Also I noticed we don't have option to MAP few things as :
1. RX1 AF
2. CTUNE
etc.
73s
Prem
Thanks for compliment.
We miss the Freq read out when away from PC screen ! We should be able to see the freq ! Rest all OK .
Also I noticed we don't have option to MAP few things as :
1. RX1 AF
2. CTUNE
etc.
73s
Prem
- Tue Dec 05, 2017 9:15 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
So we cant do the frequency displayed in OSC screen.
Please find attached the layout details I prepared modifying your layout and referring to some other sample layouts.
I have 3 Pages in my Layout as attached. If anyone interested, I can share the OSC design data file.
73s
Prem
So we cant do the frequency displayed in OSC screen.
Please find attached the layout details I prepared modifying your layout and referring to some other sample layouts.
I have 3 Pages in my Layout as attached. If anyone interested, I can share the OSC design data file.
73s
Prem
- Mon Dec 04, 2017 12:41 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
I designed my OSC layout which cover most of functions on PSDR screen.
I like to add option to display VFO Freq display in OSC layout. Is that function available ??
73s,
Prem
I designed my OSC layout which cover most of functions on PSDR screen.
I like to add option to display VFO Freq display in OSC layout. Is that function available ??
73s,
Prem
- Mon Dec 04, 2017 6:57 am
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 200D RX2 ADC Overload
- Replies: 7
- Views: 8314
Re: 200D RX2 ADC Overload
Hi Scott,
I could not get it understood !!
Is it the strong signals that cause this ??
73s
Prem
I could not get it understood !!
Is it the strong signals that cause this ??
73s
Prem
- Sun Dec 03, 2017 10:26 am
- Forum: Everything Else: Antennas, Relays, Switches, Power, Grounding, Cooling, etc.
- Topic: 200D RX2 ADC Overload
- Replies: 7
- Views: 8314
Re: 200D RX2 ADC Overload
Hi Team,
I get ADC Overload Flag when I run CuSDR with my Hermes.
Also once in a while with PSDR mRx 3.4 (latest Ver).
What is the reason for this ADC over load ? What we have to do to clear this ?
73s,
Prem
I get ADC Overload Flag when I run CuSDR with my Hermes.
Also once in a while with PSDR mRx 3.4 (latest Ver).
What is the reason for this ADC over load ? What we have to do to clear this ?
73s,
Prem
- Wed Nov 29, 2017 12:28 pm
- Forum: PowerSDR mRX
- Topic: PowerSDR mRX PS 3.4.6 Released
- Replies: 33
- Views: 27221
Re: PowerSDR mRX PS 3.4.6 Released
Hi Kelvin,
In my set up with Hermes, I notice my AGC gain jump to 93 when I open set up screen and cancel it to close ! Hope our Master Scott will also have a look into this.
73s
Prem
In my set up with Hermes, I notice my AGC gain jump to 93 when I open set up screen and cancel it to close ! Hope our Master Scott will also have a look into this.
73s
Prem
- Tue Nov 28, 2017 5:30 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott, It was a mistake from my side to get the samples from a different folder ! I was checking some where ! :) How is the impact of "Custom sized Layout" as seen in your layout ? I was trying to make a new layout modifying your layout. Notice some controls behave as if I pressed some ...
- Mon Nov 27, 2017 5:35 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
I had used 64 bit OSC editor for windows.
Ver 1.8.4 win64.zip
Is that ok or not ?
73s,
Prem
I had used 64 bit OSC editor for windows.
Ver 1.8.4 win64.zip
Is that ok or not ?
73s,
Prem
- Sun Nov 26, 2017 3:32 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi,
Can anyone tell me the idea to set Channel for different controls in Touch OSC Layout like Button, Slider etc. ?
Is the Channel number same for all controls in a Page or in a Layout ?
73s
Prem
Can anyone tell me the idea to set Channel for different controls in Touch OSC Layout like Button, Slider etc. ?
Is the Channel number same for all controls in a Page or in a Layout ?
73s
Prem
- Sun Nov 26, 2017 3:29 pm
- Forum: PowerSDR mRX
- Topic: PowerSDR mRX PS 3.4.6 Released
- Replies: 33
- Views: 27221
Re: PowerSDR mRX PS 3.4.6 Released
Hi Scott,
It was some configuration error locally in my machine !
Now I find it is ok. No error.
73s
Prem
It was some configuration error locally in my machine !
Now I find it is ok. No error.
73s
Prem
- Sat Nov 25, 2017 5:40 pm
- Forum: PowerSDR mRX
- Topic: PowerSDR mRX PS 3.4.6 Released
- Replies: 33
- Views: 27221
Re: PowerSDR mRX PS 3.4.6 Released
Hi Scott,
I have installed 3.4.6 and notice that when VOX enable, MOX get enables.
Please have a look and advice it is due to some trouble in my system ?
73s,
Prem
I have installed 3.4.6 and notice that when VOX enable, MOX get enables.
Please have a look and advice it is due to some trouble in my system ?
73s,
Prem
- Sat Nov 25, 2017 6:39 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Dear Scott,
Well , noted. Thank you very much.
I checked the open option in touch OSC Editor to see samples available there. But all folders are empty and so I could not find any sample Layouts there to give a try. I only have yours and that one did not use a rotary Vol control.
73s,
Prem
Well , noted. Thank you very much.
I checked the open option in touch OSC Editor to see samples available there. But all folders are empty and so I could not find any sample Layouts there to give a try. I only have yours and that one did not use a rotary Vol control.
73s,
Prem
- Thu Nov 23, 2017 5:32 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott, I could make it working with new Database. I removed all files from PSDR mRx folder and then imported my old database. But I loose some newly created TX Profiles. Can I get it back ? Hi Team, Can anyone help me to configure and use rotary type slider to use as Vol control, Mic Gain etc . ?...
- Wed Nov 22, 2017 12:54 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
PSDR fail to run now. Means program fail to open.
I tried after reinstalling PSDRmRx 3.4.3. Still same error.
Need to delete old database ? I dont know where it is lying. Can you help me to correct it please ?
Thanks and Regards,
Prem.
PSDR fail to run now. Means program fail to open.
I tried after reinstalling PSDRmRx 3.4.3. Still same error.
Need to delete old database ? I dont know where it is lying. Can you help me to correct it please ?
Thanks and Regards,
Prem.
- Wed Nov 22, 2017 12:19 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott, I was trying to prepare one custom Layout for me starting from your layout. I have some doubts as : 1. Any special setting need when I place a button and a label over it ? 2. Settings for Rotary controller ?? 3. Specialty of Multi push ?? 4. Difference between individual Buttons and Multi ...
- Mon Nov 20, 2017 6:18 am
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott, I could make it working. Thanks for advice. For the rest of team who are new to this , I am posting here the settings I made it to work. 1. Download and install Touch OSC Bridge and Run it. 2. Download and install and Run Touch OSC Editor. Build our Panel as required to control PSDR from T...
- Sun Nov 19, 2017 5:57 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott,
It is installed on my PC. But still not communicate.
When I run OSC Bridge, cant see any running programme !!
i think OSC Bridge do not run . I cant see any program as OSC Bridge running .
Any further sugession ?
73s
Prem
It is installed on my PC. But still not communicate.
When I run OSC Bridge, cant see any running programme !!
i think OSC Bridge do not run . I cant see any program as OSC Bridge running .
Any further sugession ?
73s
Prem
- Sun Nov 19, 2017 5:19 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi Scott, I installed touch OSC in my iPad (Paid version) . Installed Editor in my PC (free version) . Made a simple layout with a push button. Then downloaded layout to iPad. My PSDR identify touch OSC. But I am not able to communicate from iPad to PSDR. Do we need to buy editor paid version ? Any ...
- Sun Nov 19, 2017 3:22 pm
- Forum: Macro & MIDI Controller Software, Hardware & Scripts
- Topic: TouchOSC custom tablet MIDI control surface
- Replies: 47
- Views: 47882
Re: TouchOSC custom tablet MIDI control surface
Hi,
I purchased TOUCH OSC for my Ipad and need to use it for my Hermes. Is there any detailed tutorial to INSTALL and configure step by step ?
73s,
Prem
I purchased TOUCH OSC for my Ipad and need to use it for my Hermes. Is there any detailed tutorial to INSTALL and configure step by step ?
73s,
Prem