Additional 1 year warranty on orders placed upto 25th of February 2023.

3-4 weeks lead time, You will be charged $1000 now and the balance of $2395.00 plus shipping $95 when the radio is ready to ship.

Review of the ANAN-7000DLE MKII by Bob Nagy, AB5N

eHAM Reviews

The ANAN-7000DLE – Second to none!

• Using Direct Down Conversion with an ultra low phase noise clock yields an RMDR of 116dB @ 2Khz separation, this means that close in weak signals will not be masked by the receiver’s phase noise.
• The transmitter specifications are also off the chart, use of a new 16bit DAC with an ultra low noise clock source results in transmit phase noise better than any other product available in the market.
• Use of LDMOS drivers and an optimized final Amplifier stage with adaptive Predistortion Algorithm (PureSignal) yields transmit IMD of -68db @ 100W PEP, this is at least 20dB better than any Class A transmitter and over 30dB better than the competition.
• Use of two 16bit phase synchronous ADCs allow for advanced applications such as Diversity reception for ultimate noise mitigation and effects of signal fading.

The ANAN-7000DLE HF & 6M 100W SDR Transceiver offers top of the line performance is a compact rugged package, it is based on the work of the OpenHPSDR community.

Improvements:

1. Rugged Aluminium Extruded chassis for excellent thermal dissipation and Rx/Tx isolation.
2. PA board improvements for higher duty cycle, 100% ICAS duty cycle supported.
3. Tx Signal generation redesigned to improve SNR at low power levels.

Specifications:

General Specifications:

• Architecture: Direct Sampling DDC/DUC Transceiver
• Interface: Ethernet
• Phase Noise (Clock): -149dB @ 10Khz
• TCXO Stability (Typical): /- .1 PPM
• Modes: CW, SSB, NFM, AM, Digital
• Antenna Ports: Three BNC 50 ohms Software Configurable Ports, Three BNC ADC1 Bypass and Loop in ports, One BNC for RX2
• Frequency Resolution: 1 Hz

Electrical Specifications:

• 13.8v DC @ 25A, 3A Receive/25A Transmit

Mechanical Specifications:

• 5Kg (approx. Weight)
• Dimensions: 276MM (L) x 79MM (H) x 265MM (W) (Not including extrusions)
• Rugged Aluminum Extrusion with Temperature controlled internal/External (Optional) Fan.

Receiver Specifications:

• Receiver Architecture: Direct Down Conversion
• Dual 16 bit Phase Synchronous ADCs
• Independent filter banks for each ADC
• 6M LNAs
• Frequency Coverage: 9Khz to 60Mhz
• Attenuator: 1-30dB step attenuator
• Reciprocal Mixing Dynamic Range (RMDR): 116dB @ 2Khz offset
• Receiver Phase noise: -149dB @ 10Khz
• Image rejection: 90dB
• Hardware support for 7 independent receivers assignable to either ADC

Transmitter Specifications:

• Transmitter Architecture: Direct Up Conversion
• DAC Resolution: 16 bit
• RF Output Power: 100W PEP SSB, FM, RTTY, Digital; 1-30W AM, 100W CW
• IMD: IMD3 typically -68dB below PEP @ 100W output on 20M
• Harmonics: Typically better than -43dBc on HF and -60dBc on 6M
• Carrier and Opposite Sideband Suppression: Better than -80dBc
• Transverter IF Output: 0db to 15dB

IOs:

• RCA Line In, Digital Inputs, PTT in, PTT Out
• DB9 Seven Software Configurable Open Collector Outputs
• SMA XVTR, 10Mhz reference Input
• 3.25mm Barrel Mic, CW Key, Headphones and  two 6.25mm Speaker Outputs
• RJ45 Ethernet LAN Connector