ANAN-7000DLE MKII 100W HF & 6M Transceiver (No Embedded PC)

$3395.00 $2795.00
  • Description
  • Technical Specifications
  • Reviews

PLEASE NOTE : ON CHECKOUT PLEASE USE PAYPAL ONLY FOR PAYMENT AS THE CREDIT CARD GATEWAY IS NOT FUNCTIONAL AT THE MOMENT.

 

The ANAN-7000DLE – Second to none!

  • Using Direct Down Conversion with an ultra low phase noise clock yields an RMDR of 116dB @ 2Khz separation, this means that close in weak signals will not be masked by the receiver’s phase noise.
  • The transmitter specifications are also off the chart, use of a new 16bit DAC with an ultra low noise clock source results in transmit phase noise better than any other product available in the market.
  • Use of LDMOS drivers and an optimized final Amplifier stage with adaptive Predistortion Algorithm (PureSignal) yields transmit IMD of -68db @ 100W PEP, this is at least 20dB better than any Class A transmitter and over 30dB better than the competition.
  • Use of two 16bit phase synchronous ADCs allow for advanced applications such as Diversity reception for ultimate noise mitigation and effects of signal fading.

The ANAN-7000DLE HF & 6M 100W SDR Transceiver offers top of the line performance is a compact rugged package, it is based on the work of the OpenHPSDR community.

Improvements:

  1. Stainless steel chassis and large aluminium heatsink for excellent thermal dissipation and Rx/Tx isolation.
  2. PA board improvements for higher duty cycle, 100% ICAS duty cycle supported.
  3. Tx Signal generation redesigned to improve SNR at low power levels.

 

2 week Lead time

 

Specifications:

 

General Specifications:

  • Architecture: Direct Sampling DDC/DUC Transceiver
  • Interface: Ethernet
  • Phase Noise (Clock): -149dB @ 10Khz
  • TCXO Stability (Typical): /- .1 PPM
  • Modes: CW, SSB, NFM, AM, Digital
  • Antenna Ports: Three BNC 50 ohms Software Configurable Ports, Three BNC ADC1 Bypass and Loop in ports, One BNC for RX2
  • Frequency Resolution: 1 Hz

 

Electrical Specifications:

  • 13.8v DC @ 25A, 3A Receive/25A Transmit

 

Mechanical Specifications:

  • 10Kg (approx. Weight)
  • Dimensions: 384MM (W) x 114MM (H) x 310MM (D) (Not including extrusions)
  • Rugged Steel Chassis and Aluminum heatsink with Temperature controlled internal/External (Optional) Fan.

 

Receiver Specifications:

  • Receiver Architecture: Direct Down Conversion
  • Dual 16 bit Phase Synchronous ADCs
  • Independent filter banks for each ADC
  • 6M LNAs
  • Frequency Coverage: 9Khz to 60Mhz
  • Attenuator: 1-30dB step attenuator
  • Reciprocal Mixing Dynamic Range (RMDR): 116dB @ 2Khz offset
  • Receiver Phase noise: -149dB @ 10Khz
  • Image rejection: 90dB
  • Hardware support for 7 independent receivers assignable to either ADC

 

Transmitter Specifications:

  • Transmitter Architecture: Direct Up Conversion
  • DAC Resolution: 16 bit
  • RF Output Power: 100W PEP SSB, FM, RTTY, Digital; 1-30W AM, 100W CW
  • IMD: IMD3 typically -68dB below PEP @ 100W output on 20M
  • Harmonics: Typically better than -43dBc on HF and -60dBc on 6M
  • Carrier and Opposite Sideband Suppression: Better than -80dBc
  • Transverter IF Output: 0db to 15dB

 

IOs:

  • RCA Line In, Digital Inputs, PTT in, PTT Out
  • DB9 Seven Software Configurable Open Collector Outputs
  • SMA XVTR, 10Mhz reference Input
  • 3.25mm Barrel Mic, CW Key, Headphones and  two 6.25mm Speaker Outputs
  • RJ45 Ethernet LAN Connector

Downloads

Subscribe Newsletter
To get the latest scoop right to your inbox.

Help Centre